Mathematics, 07.05.2020 00:08 joelpimentel

G(x) = x^3+ 5 x
(x) = 2x - 2
Find (g(f))(x)

Answers: 2

Show answers

Another question on Mathematics

Mathematics, 21.06.2019 17:30

Adriver from the university of florida women’s swimming and diving team is competing in the in ncaa zone b championships

Answers: 3

Answer

Mathematics, 21.06.2019 18:30

Which of the following is the result of expanding

Answers: 2

Answer

Mathematics, 21.06.2019 18:40

What is the value of the expression below? 148+(-6)| + |– 35= 7|

Answers: 2

Answer

Mathematics, 22.06.2019 01:00

How would you find the height of points on the circle? the topic is trigonometry.

Answers: 3

Answer

You know the right answer?

G(x) = x^3+ 5 x
(x) = 2x - 2
Find (g(f))(x)...

Questions

Engineering, 26.07.2019 17:20

Initially there are 3 [kg) of gas at a pressure of 200 [kpa] and specific volume of 1.5 [m3/kgl contained within a piston cylinder assembly. the gas u...

Engineering, 26.07.2019 17:20

In machining, if the cost to purchase/regrind the cutting tool=$0.00, the optimum speed for machining time minimization would be different from the op...

Engineering, 26.07.2019 17:20

In turning, if the spindle speed (spindle rpm) increases by a factor of four, while the feed rate decreases by a factor of four, will the ideal surfac...

Engineering, 26.07.2019 17:20

Oil, with a density of ρ = 900 kg m=3 and a kinematic viscosity of v = 0.1 m^2 s^-1, flows at a volume flow rate of q 0.2 m^3 s^-1 through 500 m of 20...

Engineering, 26.07.2019 17:20

What is an involute profile and why is it used in gear tooth design?...

Engineering, 26.07.2019 17:20

If i can live with a 3% probability of failure, select a ball bearing design (independent of shaft diameter that will carry a 120 ib load at 3000 rpm....

Engineering, 26.07.2019 17:20

Determine the diameter of a cylindrical capillary tube needed to observe a 0.4" rise for water if the contact angle is 12°...

Engineering, 26.07.2019 17:20

If a cutting operation is performed at a feed rate of 5 in/min, and the feed is 0,005 in/rev, then the spindle rpm is: i. 5000 rpm. i. 1000 rpm. ili....

Engineering, 26.07.2019 17:20

Describe the general steps in the journal bearing design procedure. outline approach with substeps identified is fine....

Engineering, 26.07.2019 17:20

How are the pressure angle, pitch circle and base circle for a gear set related?...

Engineering, 26.07.2019 17:20

You need to design a compound reverted gear train with a 25: 1 gear ratio. (a) explain how you would go about developing this design. (b) if you were...

Engineering, 26.07.2019 17:20

One of the following is an extensive property: a)- density b)- volume c)- pressure d)-none of the above...

Engineering, 26.07.2019 17:20

1.0 kg of air at 300 k and 100 kpa (state 1) is slowly compressed in a piston cylinder (closed system). the compression process is an isothermal proce...

Engineering, 26.07.2019 17:20

Tool wear rate decreases with increasing: i. machining velocity and work material hardness. ii. cutting tool hardness. ii. none of the above. iv. not...

Engineering, 26.07.2019 17:20

Define the following terms. a drawing with the terms labeled would also be where appropriate. a. pitch circle/pitch diameter b. pinion/gear c. base c...

Engineering, 26.07.2019 17:20

5kg of wood is burnt in an insulated room. take the walls of the room as well as the wood as the system. the internal energy of the room will increase...

Engineering, 26.07.2019 17:20

The hardness of a cutting tool increases with increasing temperature. thus, it is always convenient to machine at higher speeds that lead to higher te...

Engineering, 26.07.2019 17:20

What are the independent and dependent variables that are taken into account during journal bearing design?...

Engineering, 26.07.2019 17:20

You are provided with an epicyclic (planetary) gear train with the following 30, 20 and 70 teeth on the sun, planet and ring gear respectively. (a) dr...

Engineering, 26.07.2019 17:20

What is a partial bearing? what is a loading situation that might lead you to use a partial bearing? how did this tie into beauchamp tower's experim...

More questions: Mathematics Another questions

G(x) = x^3+ 5 x (x) = 2x - 2 Find (g(f))(x)

Answers

Another question on Mathematics

G(x) = x^3+ 5 x
(x) = 2x - 2
Find (g(f))(x)