subject

Mathematics, 24.10.2019 07:43 maskythegamer

Easy points of you answer this ! so me out

Easy points of you answer this ! so me out

ansver

Answers: 2

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 19:00

Which of the expressions (on the photo document i inserted) together represent all solutions to the following equation? 8cos(12x)+4=-4 *the answer should be in degrees.* > i would like for someone to explain the process to find the solutions for this.

Answers: 2

question

Mathematics, 22.06.2019 02:00

Th perimeter of a rectangular garden is 150 feet. the length is 50 feet longer than the width, w. which equation could be used to calculate the width of the garden? a.) 2w+ 2(w-50) =150 b.) 2w+50 + 2w =150 c.) 2(w+50) + w =150 d.) 2w+ 2(w + 50) = 150 need asap. will give brainliest !

Answers: 1

question

Mathematics, 22.06.2019 02:40

On which number line are -3 and its opposite shown

Answers: 3

question

Mathematics, 22.06.2019 03:00

Which angle of rotation is an angle of rotational symmetry for all figures?

Answers: 1

You know the right answer?

Easy points of you answer this ! so me out
...

Questions

question

Engineering, 26.07.2019 17:20

Describe the general steps in the journal bearing design procedure. outline approach with substeps identified is fine....

question

Engineering, 26.07.2019 17:20

How are the pressure angle, pitch circle and base circle for a gear set related?...

question

Engineering, 26.07.2019 17:20

You need to design a compound reverted gear train with a 25: 1 gear ratio. (a) explain how you would go about developing this design. (b) if you were...

question

Engineering, 26.07.2019 17:20

One of the following is an extensive property: a)- density b)- volume c)- pressure d)-none of the above...

question

Engineering, 26.07.2019 17:20

1.0 kg of air at 300 k and 100 kpa (state 1) is slowly compressed in a piston cylinder (closed system). the compression process is an isothermal proce...

question

Engineering, 26.07.2019 17:20

Tool wear rate decreases with increasing: i. machining velocity and work material hardness. ii. cutting tool hardness. ii. none of the above. iv. not...

question

Engineering, 26.07.2019 17:20

Define the following terms. a drawing with the terms labeled would also be where appropriate. a. pitch circle/pitch diameter b. pinion/gear c. base c...

question

Engineering, 26.07.2019 17:20

5kg of wood is burnt in an insulated room. take the walls of the room as well as the wood as the system. the internal energy of the room will increase...

question

Engineering, 26.07.2019 17:20

The hardness of a cutting tool increases with increasing temperature. thus, it is always convenient to machine at higher speeds that lead to higher te...

question

Engineering, 26.07.2019 17:20

What are the independent and dependent variables that are taken into account during journal bearing design?...

question

Engineering, 26.07.2019 17:20

You are provided with an epicyclic (planetary) gear train with the following 30, 20 and 70 teeth on the sun, planet and ring gear respectively. (a) dr...

question

Engineering, 26.07.2019 17:20

What is a partial bearing? what is a loading situation that might lead you to use a partial bearing? how did this tie into beauchamp tower's experim...

question

Engineering, 26.07.2019 17:20

Define and give a few benefits of each of three gear train design options?...

question

Engineering, 26.07.2019 17:20

The atmospheric pressure at the top and the bottom of a mountain are read to be 93.8 kpa and 100.5 kpa respectively. if the average density of air is...

question

Engineering, 26.07.2019 17:20

What are some of the assumptions that were used in developing the 1d reynolds flow equation?...

question

Engineering, 26.07.2019 17:20

Acar engine rotates at a speed of 3500 rpm and transmits 290 kw. determine the torque applied to the crankshaft of the car a)- 791.2 n. m b)- 1108 n....

question

Engineering, 26.07.2019 17:20

The pressure of a fluid at rest changes with vertical distance but remains the same in the horizontal direction a)-true b)-false...

question

Engineering, 26.07.2019 17:20

Agear set uses of an 18-tooth pinion, has a diametral pitch of 8 teeth in and a pressure angle of ? -20 . the pinion runs at 750 rev/min and drives a...

question

Engineering, 26.07.2019 17:20

Aresistor heater is used for heating water for 3 minute at 120 volts and s amps. how much of the electrical power is consumed? a)- 1800w b)- 108 kw c...

question

Biology, 26.07.2019 17:20

When paleontologist refer to the "big five" to what are they referring?...

More questions: Mathematics Another questions

Questions on the website: 13722361