subject

Biology, 20.03.2020 08:19 hunterkerlin20p3l6ff

What do you think would happen to a cell if enzymes were not
present?

ansver

Answers: 2

Show answers

Another question on Biology

question

Biology, 21.06.2019 15:00

Disinfection of impression materials is usually accomplished by a. sterilization with high heat. b. spray or immersion in a chemical disinfectant. c. sterilization with steam under pressure. d. allowing the impression to sit 24 hours in water until all the organisms die.

Answers: 2

question

Biology, 21.06.2019 19:00

Consider the diagram below, which represents components of the biosphere. what do the two arrows in the diagram most likely represent? a. radiation b. photosynthesis c. cellular respiration d. energy conversions will give to anyone who answers quickly

Answers: 1

question

Biology, 22.06.2019 13:10

Which of the following best describes the purpose of the parathyroid hormone? a. it decreases the blood calcium level and decreases blood phosphorus level. b. it decreases the blood calcium level and increases the blood phosphorus level. c. it increases the blood calcium level and increases blood phosphorus level. d. it increases the blood calcium level and decreases blood phosphorus level.

Answers: 2

question

Biology, 22.06.2019 17:50

How does a catalyst influence a chemical reaction?

Answers: 1

You know the right answer?

What do you think would happen to a cell if enzymes were not
present?...

Questions

question

Engineering, 11.07.2019 01:10

Water is subjected to various temperatures and pressures as indicated below draw a separate p-v and t-v diagram that includes lines of constant tand/o...

question

Engineering, 11.07.2019 01:10

Centrifugal pumps are the most commonly used in process industries. a rotodynamic pump in its simplest form consists of an impeller rotating inside a...

question

Engineering, 11.07.2019 01:10

One hundred kilojoules of heat are transferred from a heat reservoir at 600 k to the environment at 300 k. a)- find the change in entropy of each rese...

question

Engineering, 11.07.2019 01:10

An inventor claimed that a cyclic engine produces 0.4 kj of work per kj of heat extracted from a heat reservoir. a)- the cycle operates between 380 °c...

question

Engineering, 11.07.2019 01:10

Determine the laplace transform for the function below using integration of the laplace transform formula (i. e. use integration by parts) f(t)=3te^-2...

question

Engineering, 11.07.2019 01:10

Consider an airplane cruising at an altitude of 30 km where standard atmospheric conditions are (- 50°c) and 26.5 kpa at a speed of 800 km/h. each win...

question

Engineering, 11.07.2019 01:10

Oil enters a counterflow heat exchanger at 525 k with a mass flow rate of 10 kg/s and exits at 350 k. a separate stream of liquid water enters at 20°c...

question

Engineering, 11.07.2019 01:10

1a)-solve the following differential equation using laplace transforms. assume zero initial conditions x(t) +2x(t)= 4us(t) 2b)- plot the solution x(t)...

question

Engineering, 11.07.2019 01:10

Asimple brayton cycle is working under the following conditions: working fluid: air pressure ratio: 8 minimum and maximum temperatures of the cycle...

question

Engineering, 11.07.2019 01:10

Determine the highest root of f(x)=2x^3-11.7x^2+ 17.7x - 5 (in the domain x [2.5, 4]) and the approximate percent relative errors for your solutions,...

question

Engineering, 11.07.2019 01:10

Acomposite spherical tank made of three different materials in series with inside and outside convection. a)-draw the schematic of the system. b)-draw...

question

Engineering, 11.07.2019 01:10

Afelix baumgartner had an estimated mass of 120 kg and a frontal area of 0.9 m 2. he pulled his parachute at 2.5 km where the density of the atmospher...

question

Engineering, 11.07.2019 01:10

Ariver flowing steadily at a rate of 175 m^3/s is considered for hydroelectric power generation. it is determined that a dam can be built to collect w...

question

Engineering, 11.07.2019 01:10

Acantilevered boom is part of an assembly machine and is made of from a steel beam s4x7.7. a tool with a weight of 650 lb moves continuously from the...

question

Engineering, 11.07.2019 01:10

The boeing 747 is an air plane often equipped with four pratt and whitney jt9d engines that can each offer 193.50 kn of thrust. the air plane has a cr...

question

Engineering, 11.07.2019 01:10

What is the n exponent? a)- 0.701242 b)-0.708783 c)- 0.71179s d)- 0.787829 e)- 0.86154...

question

Engineering, 11.07.2019 01:10

What is the percentage of error involved in treating carbon dioxide at 7 mpa and 380 k as an ideal gas?...

question

Engineering, 11.07.2019 01:10

Apiston-cylinder device contains 0.1 kg of hydrogen gas (pg model: cv=10.18, k = 1.4, r= 4.12 kj/kg-k) at 1000 kpa and 300 k. the gas undergoes an ex...

question

Engineering, 11.07.2019 01:10

Which one of the following is correct? a)- movement of dislocations is not the primary mechanism of plastic behavior in polymers. b)- interstitial di...

question

Engineering, 11.07.2019 01:10

What is the operating flowrate (msef/d) from the bottomhole nodal template? a)-1352 b)-1400 c)-1653 d)- 1680 e)- 1752...

More questions: Biology Another questions

Questions on the website: 13722367