Physics, 21.02.2022 22:10 datgamer13

See Hint Rank the following in order of size, from smallest to largest.
Items in order
Items (6 items)
(Drag and drop into the appropriate area)
Smallest
A light-year
A light-hour
The radius of Earth
No more
items
A light-minute
The radius of the Solar
System
The distance from Earth to
the Sun
O OF 15 QUESTIONS COMPLETED
< 02/15 >
4 VIEW SOLUTION
►SUBMIT ANSWER

Answers: 3

Show answers

Another question on Physics

Physics, 22.06.2019 08:30

Abike rider starts from rest and accelerates 28.0 meters down a slope in 5.00 seconds. what is her acceleration? select one: a. 3.21 m/sec2 b. 1.75 m/sec2 c. 9.80 m/sec2 d. 2.24 m/sec2

Answers: 3

Answer

Physics, 22.06.2019 16:00

Rank the six combinations of electric charges on the basis of the electric force acting on q1. define forces pointing to the right as positive and forces pointing to the left as negative. rank positive forces as larger than negative forces. q1,q2,q3 = positive(+) q1 = + q2 = + q3 = - q1 = + q2= - q3= + q1= - q2= + q3= + q1= + q2= - q3= - q1,q2,q3 = negative

Answers: 1

Answer

Physics, 22.06.2019 17:00

Adiver named jacques observes a bubble of air rising from the bottom of a lake (where the absolute pressure is 3.50 atm) to the surface (where the pressure is 1.00 atm). the temperature at the bottom is 4.00 ∘c, and the temperature at the surface is 23.0 ∘c.what is the ratio of the volume of the bubble as it reaches the surface (vs) to its volume at the bottom (vb)? if jaques were to hold his breath the air in his lungs would be kept at a constant temperature. would it be safe for jacques to hold his breath while ascending from the bottom of the lake to the surface?

Answers: 1

Answer

Physics, 23.06.2019 08:30

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

Answer

You know the right answer?

See Hint Rank the following in order of size, from smallest to largest.
Items in order
...

Questions