Physics, 01.07.2021 08:50 mythic61

(Serious Please) patulong

Answers: 1

Show answers

Answers

Answer from: jenniferleeross53

a. Potential energy is highest at Part A

The kinetic energy is highest at Part C and Part D

b. The potential energy is lowest at Part C and Part D

c. The roller coater has equal amount of potential and kinetic energy at Part B, Part D and part F

2) Yes, the mechanical energy is the same from point A to F according to the first law of thermodynamics

Explanation:

The total mechanical energy is constant where the roller coaster moves by only the initial velocity, and the the force of gravity

Total mechanical energy, M.E. = Kinetic energy, K.E. + Potential energy, P.E.

M.E. = K.E. + P.E. = Constant

Therefore, we have;

a. Potential energy is the energy stored in a body, due to its position or elevation, state or arrangement

The higher the elevation, the higher the potential energy, therefore, the highest amount of potential energy is gained when the roller coaster is at the highest point in the motion = Part A

From M.E. = K.E. + P.E. = Constant, the highest kinetic energy is given at the point the roller coaster has the lowest potential energy, which corresponds with the lowest points = Part C and Part D

b. Potential energy, which is the energy of body due to its position or state is lowest at the lowest points = Part C and Part D

c. The value of potential energy, P.E. due to elevation, can be found as follows

P.E. = Mas, m × Gravity, g × Height, h

Therefore, the potential energy will be half the maximum value where the height, h = (Maximum height)/2 and given that M.E. = K.E. + P.E., the kinetic energy, will increase by the same amount, and we have;

K.E. = P.E. at the half the maximum height of the track = Part B, Part D and part F

2) The mechanical energy is the input energy, which according to the first law of thermodynamics cannot be created and destroyed an it is therefore, constant and it is the same from point A to F

Answer from: Quest

none, its a machine

Answer from: Quest

a straight line sloped

Another question on Physics

Physics, 22.06.2019 00:00

Did the proton move into a region of higher potential or lower potential? did the proton move into a region of higher potential or lower potential? because the proton is a negative charge and it accelerates as it travels, it must be moving from a region of higher potential to a region of lower potential.because the proton is a negative charge and it accelerates as it travels, it must be moving from a region of lower potential to a region of higher potential.because the proton is a positive charge and it slows down as it travels, it must be moving from a region of higher potential to a region of lower potential.because the proton is a positive charge and it slows down as it travels, it must be moving from a region of lower potential to a region of higher potential.request answerpart bwhat was the potential difference that stopped the proton? express your answer with the appropriate units.î”v î” v = nothingnothingrequest answerpart cwhat was the initial kinetic energy of the proton, in electron volts? express your answer in electron volts.ki k i = nothing ev request answerprovide feedback

Answers: 2

Answer

Physics, 22.06.2019 09:50

Which statement correctly describes the current in a circuit that is made up of any two resistors connected in parallel with a battery? a. the current in the battery and in each resistor is the same b. the current the battery equals to the sum of the currents in the resistors c.the current in the battery is less than the current in either resistor d. the current in the battery equals to the product of the currents in the resistors

Answers: 1

Answer

Physics, 22.06.2019 12:30

An ice-making machine inside a refrigerator operates in a carnot cycle. it takes heat from liquid water at 0.0 degrees celsius and rejects heat to a room at a temperature of 19.2 degrees celsius. suppose that liquid water with a mass of 76.3kg at 0.0 degrees celsius is converted to ice at the same temperature. take the heat of fusion for water to be l_f = 3.34*10^5 j/kg.how much energy e must be supplied to the device? express your answer in joules.

Answers: 1

Answer

Physics, 22.06.2019 21:00

Ais a machine that makes work easier when a single force is applied. a simple machine b compound machine c endangered machine d complex machine

Answers: 2

Answer

You know the right answer?

(Serious Please) patulong
...

Questions