subject
Physics, 30.06.2021 02:20 katemsoo

an ideal gas occupies 400m3 at a pressure of 250 pa. if the volume is changed to 100m3 at constant temperature, what will be the new pressure of the gas​

ansver
Answers: 1

Another question on Physics

question
Physics, 22.06.2019 11:00
A0.580-kg rock is tied to the end of a string and is swung in a circle with a radius of 0.500 meters. the velocity of the rock is 4.50 m/s. what is the centripetal force acting on the rock? 15.5 n 5.22 n 69.8 n 23.5 n
Answers: 3
question
Physics, 23.06.2019 00:10
During cooling, the kinetic energy of the molecules falls. why does this happen? a.the motion of the molecules increases. b. the motion of the molecules slows down. c.the van der waals forces between molecules decrease d. the forces of attraction between the molecules are overcome.
Answers: 2
question
Physics, 23.06.2019 08:00
Athin electrical heater is inserted between a long circular rod and a concentric tube with inner and outer radii of 20 and 40 mm. the rod (a) has a thermal conductivity of ka = 0.15 w/(m*k), while the tube (b) has a thermal conductivity of kb = 0.8 w/(m*k) and its outer surface is subjected to convection with a fluid of temperature t= -15°c and heat transfer coefficient 60 w/(m2 *k). the thermal contact resistance between the cylinder surfaces and the heater is negligible. (a) determine the electrical power per unit length of the cylinders (w/m) that is required to maintain the outer surface of cylinder b at 15°c. (b) what is the temperature at the center of cylinder a?
Answers: 2
question
Physics, 23.06.2019 08:30
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
You know the right answer?
an ideal gas occupies 400m3 at a pressure of 250 pa. if the volume is changed to 100m3 at constant t...
Questions
question
Mathematics, 15.06.2021 17:20
question
English, 15.06.2021 17:20
question
Biology, 15.06.2021 17:20
question
Mathematics, 15.06.2021 17:20
question
English, 15.06.2021 17:20
Questions on the website: 13722366