The temperature of water in a beaker is 45°c. what does this measurement represent?
a) the heat capacity of water
b) the total thermal energy of water
c) the average kinetic energy of water particles
d) the total kinetic energy of water particles

Consider the growth of a 20-nm-diameter silicon nanowire onto a silicon wafer. the temperature of the wafer surface is maintained at 2400 k. assume the thermal conductivity of the silicon nanowire is 20 wm-1k-1 and all its surfaces including the tip are subjected to convection heat transfer with the coefficient h = 1×105 wm-2k-1 and t∞ = 8000 k. when the nanowire grows to l = 300 nm, what is the temperature of the nanowire tip (t (x =

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

The goal of this experiment was to answer the question, "how does diffraction occur? " suppose you formulated this alternate hypothesis: if the gap width is increased while keeping wavelength constant, then the observed diffraction will decrease because the less the ratio between wavelength and gap width is, the smaller the observed diffraction angle will be.to test this hypothesis, you would change the  gap widthdiffraction anglewavelength  and observe the  gap widthdiffraction anglewavelength  in the system.therefore, the independent variable would be the  gap widthdiffraction anglewavelength  and the dependent variable would be the  gap widthdiffraction anglewavelength.