Physics, 27.01.2020 15:31 QueenThao8933

"maximum constructive interference occurs at the

(1)
antinodes a, c, and e

(3)
antinodes b and d
(2)
nodes a, c, and e

(4)
nodes b and d
"

"maximum constructive interference occurs at the (1) antinodes a, c, a

Answers: 2

Show answers

Another question on Physics

Physics, 22.06.2019 00:10

The energy released by a chemical reaction can be measured using a calorimeter. when barium hydroxide octahydrate crystals are reacted with dry ammonium chloride inside of a coffee cup calorimeter, the temperature of the 18.00 g of water in the calorimeter decreases from 30.0°c to 8.0°c. the equation for calculating energy absorbed or released by a reaction is: where q is the energy released or absorbed, m is the mass of water in the calorimeter, cp is the specific heat of water, and δt is the observed temperature change. if the specific heat of liquid water is 4.19 j/g·°c, how much energy was absorbed by the reaction?

Answers: 3

Answer

Physics, 22.06.2019 11:00

Looking at this barometer, is the air pressure high or low? what type of weather would you expect? high, bad low, bad high, good low, good

Answers: 1

Answer

Physics, 23.06.2019 07:00

Conventional hot-water heaters consist of a tank of water maintained at a fixed temperature. the hot water is to be used when needed. the drawback is that energy is wasted because the tank loses heat when it is not in use, and you can run out of hot water if you use too much. some utility companies are encouraging the use of on-demand water heaters (also known as flash heaters), which consist of heating units to heat the water as you use it. no water tank is involved, so no heat is wasted. a typical household shower flow rate is 2.50 gal/min (9.46 l/min ) with the tap water being heated from 51.0 ˚f (10.6 ˚c) to 120 ˚f (48.9 ˚c) by the on-demand heater.what rate of heat input (either electrical of from gas) is required to operate such a unit, assuming that all the heat goes into the water?

Answers: 3

Answer

Physics, 23.06.2019 08:30

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

Answer

You know the right answer?

"maximum constructive interference occurs at the

(1)
antinodes a, c, and e

Questions