The parallel plates in a capacitor, with a plate area of 9.30 cm2 and an air-filled separation of 4.50 mm, are charged by a 7.80 V battery. They are then disconnected from the battery and pulled apart (without discharge) to a separation of 9.60 mm. Neglecting fringing, find (a) the potential difference between the plates, (b) the initial stored energy, (c) the final stored energy, and (d) the work required to separate the plates.

a) ΔV ’= 1.66 10¹ V= 16.6 V,  b)  U = 55.64 10⁻¹² J,  c)    U_f = 1.18 10⁻¹⁰ J

d)     W = 6.236 10⁻¹¹ J

Explanation:

Capacitance can be found for a parallel plate capacitor

          C = ε₀    

Let's reduce the magnitudes to the SI system

           A = 9.30 cm² (1 m / 10² cm) 2 = 9.30 10⁻⁴ m²

           c = 4.50 mm (1 m / 1000 mm) = 4.50 10⁻³ m

          Co = 8.85 10⁻¹²    9.30 10⁻⁴ /4.50 10⁻³

          Co = 1.829 10⁻¹² F

when the plates separate at d = 9.60 10⁻³ m, the capcitance changes to

          C = ε₀ \frac{A}{d_1}

          C = 8.85 10⁻¹² 9.30 10⁻⁴/9.60 10⁻³

          C = 8.57 10⁻¹³ F

a) the potential difference

            C =

since the capacitor is not discharged, let's look for the initial charge

            Co = \frac{Q}{ \Delta V}

             Q = C₀ ΔV

              Q = 1.829 10⁻¹² 7.80

             Q = 14.2662 10⁻¹² C

when the condensate plates are separated

             C = \frac{Q}{ \Delta V' }

              ΔV ’= Q / C

              ΔV ’= 14.266 10⁻¹² / 8.57 10⁻¹³

              ΔV ’= 1.66 10¹ V= 16.6 V

b) the stored energy is

             U = ½ C ΔV²

for initial separation

              U = ½ C₀ ΔV²

             U = ½ 1.829 10⁻¹² 7.80²

              U = 55.64 10⁻¹² J

c) The energy for end separation;

               U_f = ½ C DV’2

                U_f = ½ 8.57 10⁻¹³ 16,6²2

                U_f = 1.18 10⁻¹⁰ J

d) The work

as there are no losses, the work is equal to the variation of the energy

                W = ΔU = U_f -U₀

                 W = 1.18 10⁻¹⁰ - 55.64 10-12

                 W = 6.236 10⁻¹¹ J

the design of a ski jumping suit involves a trade-off between giving the skiers lift to get higher jumps and ensuring the skier does not face a lot of drag before the jump itself. an expansive suit may to lift the skier higher, but at the same time, it will also increase the air resistance. higher air resistance as the skier goes down the slope limits the speed of the jump. a big suit also increases the risk of losing balance or control, especially if there's a strong gust of wind. while technologically enhanced suits a lot, clothing is not the only factor in a ski jumper’s success. gathering speed while skiing down the slope, ensuring good speed on the ramp, and maintaining good body posture and form in the air all contribute to a ski jumper's success.