subject
Physics, 26.02.2021 22:40 zel117

If the cost per kW-hr is the same for all three appliances, how could the three household objects be ranked from MOST expensive to least expensive?


If the cost per kW-hr is the same for all three appliances, how could the three

household objects

ansver
Answers: 3

Another question on Physics

question
Physics, 22.06.2019 11:20
The ultracentrifuge is an important tool for separating and analyzing proteins. because of the enormous centripetal accelerations, the centrifuge must be carefully balanced, with each sample matched by a sample of identical mass on the opposite side. any difference in the masses of opposing samples creates a net force on the shaft of the rotor, potentially leading to a catastrophic failure of the apparatus. suppose a scientist makes a slight error in sample preparation and one sample has a mass 10 mg larger than the opposing sample. if the samples are 12 cm from the axis of the rotor and the ultracentrifuge spins at 70,000 rpm, what is the magnitude of the net force on the rotor due to the unbalanced samples? ( be thorough on your answer)
Answers: 3
question
Physics, 22.06.2019 15:30
An alien spaceship is 500 m above the ground and moving at a constant velocity of 150 m/s upwards. how high above the ground is the ship after 5 seconds?
Answers: 1
question
Physics, 22.06.2019 23:30
Which of the following forces require physical contact? tension air resistance friction magnetic force applied force
Answers: 3
question
Physics, 23.06.2019 08:30
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ฮต)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
You know the right answer?
If the cost per kW-hr is the same for all three appliances, how could the three household objects b...
Questions
question
Mathematics, 20.01.2021 16:40
question
Physics, 20.01.2021 16:40
question
History, 20.01.2021 16:40
question
Mathematics, 20.01.2021 16:40
question
Arts, 20.01.2021 16:40
question
Mathematics, 20.01.2021 16:40
question
Mathematics, 20.01.2021 16:40
question
Mathematics, 20.01.2021 16:40
question
Mathematics, 20.01.2021 16:40
question
Advanced Placement (AP), 20.01.2021 16:40
Questions on the website: 13722365