subject
Physics, 09.11.2020 22:20 cmir

A student rides their mountain bike horizontally of a 1.5 m tall ledge. if they are traveling 8.2 m/s ,how far from the ledge will they land. (hint: find time first)

ansver
Answers: 1

Another question on Physics

question
Physics, 21.06.2019 15:30
Which describe reflection? check all that apply. light bounces off a boundary.
Answers: 1
question
Physics, 23.06.2019 00:50
Aforce of 8,480 n is applied to a cart to accelerate it at a rate of 26.5 m/s2. what is the mass of the cart? 865 kg 320 kg 12.1 kg 3.12 kg
Answers: 1
question
Physics, 23.06.2019 03:30
Which statement is true? a) the work done to lift an object 6 meters is greater than the gravitational potential energy it gains. b) the work required to push an object is less than the work required to pull an object the same distance. c) the work required to raise an object to a height is equal to the gravitational potential energy the object gains. d) the work done against gravity to lift an object straight up is greater than the work required to roll it up a ramp.
Answers: 1
question
Physics, 23.06.2019 08:30
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
You know the right answer?
A student rides their mountain bike horizontally of a 1.5 m tall ledge. if they are traveling 8.2 m/...
Questions
question
Mathematics, 14.07.2019 11:30
question
Biology, 14.07.2019 11:30
question
Mathematics, 14.07.2019 11:30
Questions on the website: 13722365