Physics, 06.05.2020 08:46 Nholz809

En
Which ray diagram demonstrates the phenomenon of absorption?
) Intro

Answers: 2

Show answers

Answers

Answer from: Quest

The answer to your is is c motion and shape

Answer from: Quest

force is based upon mass and acceleration.the statement is not always true.

it can be explained from newton's second law of motion.

as per newton's second law of motion the rate of change of momentum is directly proportional to the applied force and takes place along the direction of force.

mathematically it can be written as -

$f\alpha \frac{dp}{dt}$

⇒ $f= k \frac{dp}{dt}$

here k is the proportionality constant whose value is 1.

$f=\frac{dp}{dt}$

$f= \frac{d[mv]}{dt}$

$f= m\frac{dv}{dt} +v\frac{dm}{dt}$

$f=ma+v\frac{dm}{dt}$ [a is the acceleration=dv/dt]

hence we see that force not only depends on mass and acceleration but also on velocity and rate of change of mass. force f will depend on mass and acceleration only when mass is constant.

hence the statement that force is based upon mass and acceleration is false.

Answer from: Quest

Answer: 1.4 seconds which is the third optionexplanation: current is defined as the flow of charge per timetherefore, the equation that relates current, charge and time can be expressed as follows: i = δq / δtwhere: i is the current given = 1.8 ampereδq is the charge given = 2.5 coulombδt is the time required for the flow of the given charges to give the 1.8 ampere.substitute with the givens in the above equation to get the time as follows: 1.8 = 2.5 / δtδt = 2.5 / 1.8 = 1.38888 which is approximately 1.4 secondshope this was !

Answer from: Quest

explanation:

to push or pull an object in a certain direction is known as force. a force in moving an object from one place to another.

force depends on the mass of an object. so, more is the mass of an object more will be the force required to move the object.

thus, we can conclude that the use of force to move an object is push or pull.

Another question on Physics

Physics, 22.06.2019 01:10

Asteam power plant operates on an ideal reheat rankine cycle between the pressure limits of 15 mpa and 10 kpa. the mass flow rate of steam through the cycle is 12 kg/s. steam enters both stages of the turbine at 500°c. if the moisture content of the steam at the exit of the low-pressure turbine is not to exceed 10 percent, determine (a) the pressure at which reheating takes place, (b) the total rate of heat input in the boiler, and (c) the thermal efficiency of the cycle. also, show the cycle on a t-s diagram with respect to the saturation lines. (2.15 mpa; 45.0 mw; 42.6%)

Answers: 3

Answer

Physics, 22.06.2019 09:00

A2000 kg car is rounding a curve of radius 200 m on a level road. the maximum frictional force the road can exert on the tires of the car is 4000 n. what is the highest speed at which the car can round the curve?

Answers: 1

Answer

Physics, 23.06.2019 01:00

How much work would it take to move a coulomb charge across a 4 volt potential difference?

Answers: 2

Answer

Physics, 23.06.2019 01:30

"if the pressure acting on an ideal gas at constant temperature is tripled, its volume isa) reduced to one-third.b) increased by a factor of three.c) increased by a factor of two.d) reduced to one-half"

Answers: 2

Answer

You know the right answer?

En
Which ray diagram demonstrates the phenomenon of absorption?
) Intro...

Questions