A box is pulled up a rough ramp that makes an angle of 22 degrees with the horizontal surface. The surface of the ramp is the x-plane. There is a free body diagram drawing on a block on a 22 degree incline with 5 force vectors. The first force is pointing up and parallel to the surface of the incline, labeled F Subscript T Baseline. The second force is pointing down and parallel to the surface of the incline, labeled F Subscript f Baseline = 14.8 N. The third force is pointing away from and perpendicular to the surface of the incline, labeled F Subscript N Baseline = 65 N. The fourth force is pointing into and perpendicular to the surface of the incline, labeled F Subscript g y Baseline. The fifth force is pointing straight down to the center of the earth, labeled F Subscript g Baseline = 70 N. There is another force parallel to the surface of the incline and down the hill starting at the tip of the F Subscript g y Baseline vector; it is labeled F Subscript g x Baseline.

What is the magnitude of the force of tension if the net force in the x direction of 98 N?

57 N

139 N

178 N

183 N

PLEASE EXPLAIN HOW YOU GOT ANSWER!

Aforce of 34n stretches a very light ideal spring 0.73 m from equilibrium, what is the force constant (spring constant) of the spring? (a) 47n/m (b) 38n/m (c) 53n/m (d) 25n/m

State one advantage and one disadvantage of using a plane mirrior as a driving mirrior

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28