An engineer is designing the runway for an airport. of the planes that will use
the airport, th...
![subject](/tpl/images/cats/fizika.png)
An engineer is designing the runway for an airport. of the planes that will use
the airport, the lowest acceleration rate is likely to be 3 m/s. the takeoff speed
for this plane will be 60 m/s. assuming this minimum acceleration, what is the
minimum allowed length for the runway?
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Physics
![question](/tpl/images/cats/fizika.png)
Physics, 21.06.2019 17:30
Acatapult is tested by roman legionnaires. they tabulate the results in a papyrus and 2000 years later the archaeological team reads (distances translated into modern units): range = 0.4 km; angle of launch = π/5 rad; landing height = launch height. what is the initial velocity of launch of the boulders if air resistance is negligible?
Answers: 3
![question](/tpl/images/cats/fizika.png)
Physics, 22.06.2019 02:00
The image shows a pendulum in simple harmonic motion the pendulum starts at a and swing to e
Answers: 3
![question](/tpl/images/cats/fizika.png)
Physics, 22.06.2019 12:30
Brades exam guidelines exam instructions billing & payments & support question 6 of 20 : select the best answer for the question use this illustration to answer the question below. forms & resources al programs 9 ww linics 6. in the circuit shown in the figure above, suppose that the value of r, is 100k, and the value of r2 is 470 kq. at which of the following locations in the circuit would you measure the highest voltage with your meter? rvices 999999 a. between points b and c b. between points a and b c. between points b and e d. between points a and c eredu mark for review (will be highlighted on the review page) mend < < previous question next question
Answers: 1
![question](/tpl/images/cats/fizika.png)
Physics, 23.06.2019 00:00
Determine the largest intensity w of the uniform loading that can be applied to the frame without causing either the average normal stress or the average shear stress at section b–b to exceed σ=19 mpa and τ=24 mpa, respectively.
Answers: 3
You know the right answer?
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 27.10.2020 06:30
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
History, 27.10.2020 06:30
![question](/tpl/images/cats/mat.png)
Mathematics, 27.10.2020 06:30
![question](/tpl/images/cats/es.png)
Spanish, 27.10.2020 06:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 27.10.2020 06:30
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 27.10.2020 06:30
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 27.10.2020 06:30
![question](/tpl/images/cats/mat.png)
Mathematics, 27.10.2020 06:30
![question](/tpl/images/cats/mat.png)
Mathematics, 27.10.2020 06:30
![question](/tpl/images/cats/himiya.png)
Chemistry, 27.10.2020 06:30
![question](/tpl/images/cats/en.png)