subject

Mathematics, 15.02.2022 09:50 keely6940

1)Explain why the dating techniques you used to date your artifacts worked. If the artifacts you originally selected were either not datable or not datable using the technique you selected, explain why this was the case.

ansver

Answers: 1

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 16:30

Why do interests rates on loans to be lower in a weak economy than in a strong one

Answers: 3

question

Mathematics, 21.06.2019 20:00

You are shooting hoops after school and make 152 out of a total of 200. what percent of shots did you make? what percent did you miss? show proportion(s).

Answers: 1

question

Mathematics, 21.06.2019 21:30

The domain of a function can be represented by which one of the following options? o a. a set of output values o b. a set of f(x) values o c. a set of input values o d. a set of both input and output values

Answers: 3

question

Mathematics, 21.06.2019 23:00

Y= 4x + 3 y = - 1 4 x - 5 what is the best description for the lines represented by the equations?

Answers: 1

You know the right answer?

1)Explain why the dating techniques you used to date your artifacts worked. If the artifacts you ori...

Questions

question

Chemistry, 13.09.2019 23:10

What are the characteristics of waste water from paper and pulp industry?...

question

Engineering, 13.09.2019 23:10

Acarbon/epoxy (as/3501) unidirectional laminate with a fiber orientation q = 30° is exposed to the following stresses, sx = 40 ksi, sy = -20 ksi, txy...

question

Engineering, 13.09.2019 23:10

Abody is moving with simple harmonic motion. it's velocity is recorded as being 3.5m/s when it is at 150mm from the mid-position and 2.5m/s when 225mm...

question

Engineering, 13.09.2019 23:10

Acylinder, closed by a piston, has a volume of 0.03m and contains air at 1 bar and 15°c. the air is compressed isentropically to one quarter of its or...

question

Engineering, 13.09.2019 23:10

One way to lower nox emissions in diesel engines is to add water to the fuel. since water is not mixable with diesel fuel, it has to been emulsified b...

question

Engineering, 13.09.2019 23:10

For a body moving with simple harmonic motion state the equations to represent: i) velocity ii) acceleration iii) periodic time iv) frequency v) on a...

question

Engineering, 13.09.2019 23:10

The boiler pressure is 38bar and the condenser pressure 0.032 bar. the saturated steam is superheated to 420 oc before entering the turbine. a) calcul...

question

Engineering, 13.09.2019 23:10

How much heat (btu) is prod uced by a 150-w light bulb that is on for 20-hours?...

question

Engineering, 13.09.2019 23:10

The force vector of the quadriceps muscle group is oriented at 25 degrees to the mechanical axis of the tibia, and intersects the mechanical axis of t...

question

Engineering, 13.09.2019 23:10

Assuming that the quadriceps force vector has a magnitude of 1200 n, what turning force do the quadriceps muscles apply to the shank? show your wok...

question

Engineering, 13.09.2019 23:10

Athin rectangular plate having a width w and a height h is located so that it is noenal to a moving stream of fluid. assume the drag d, that the fluid...

question

Engineering, 13.09.2019 23:10

2.4 kg of nitrogen at an initial state of 285k and 150 kpa is compressed slowly in an isothermal process to a final pressure of 600 kpa. determine the...

question

Engineering, 13.09.2019 23:10

Given the latent heat of fusion (melting) and the latent heat of vaporisation for water are δhs = 333.2 kj/kg and δhv = 2257 kj/kg, respectively. use...

question

Engineering, 13.09.2019 23:10

Logarithmic decrement. assume the damping for the mass-springdamper system in the previous problem is unknown. if the amplitude decreases by 80% every...

question

Engineering, 13.09.2019 23:10

Asquare aluminum plate 5 mm thick and 200 mm on a side is heated while vertically suspended in quiescent air at 40ºc. determine the average heat trans...

question

Engineering, 13.09.2019 23:10

Cutting speed is determined by the surface velocity of the tool. a) true b) false...

question

Engineering, 13.09.2019 23:10

Ablock of ice weighing 20 lb is taken from the freezer where it was stored at -15"f. how many btu of heat will be required to convert the ice to water...

question

Engineering, 13.09.2019 23:10

Anatural gas fuel consists of the following volumetric composition: methane, ch4: 92.5 % ethane, c2h6: 3.7 % propane, c3h8: 0.8 % nitrogen, n2: 3...

question

Engineering, 13.09.2019 23:10

Nitrogen gas is compressed in a polytropic process (n=-1.8). the initial temperature and pressure are 285 k and 150 kpa, respectively. the initial vol...

question

Engineering, 13.09.2019 23:10

Using the data below, calculate the minimum number of teeth on pinion: *remember that for teeth to round up any decimals to the nearest integer. gear...

More questions: Mathematics Another questions

Questions on the website: 13722367