subject

Mathematics, 03.03.2021 20:30 isabellatessa86

Can i have the correct answer to question 4 & 5 Please I will mark you brainliest
For number 5 the answers are at the bottom of the page.

Can i have the correct answer to question 4 & 5 Please

ansver

Answers: 1

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 20:30

William invested $5000 in an account that earns 3.8% interest, compounded annually. the formula for compound interest is a(t) = p(1 + i)t. how much did william have in the account after 6 years? (apex)

Answers: 2

question

Mathematics, 22.06.2019 01:00

During each minute of a comedy show, carlin laughs 55 times. carlin watches 33 comedy shows every day, and each show is 40 minutes long. how many times does carlin laugh every day due to the comedy shows?

Answers: 1

question

Mathematics, 22.06.2019 01:30

What is the value of x enter your answer in the box (3x+50

Answers: 2

question

Mathematics, 22.06.2019 02:30

Find the value of x to the nearest tenth. a. 4.5 b. 5.4 c. 6.3 d. 7.2

Answers: 1

You know the right answer?

Can i have the correct answer to question 4 & 5 Please I will mark you brainliest
For num...

Questions

question

Engineering, 14.09.2019 01:30

At the instant shown, rod a b lias an angular velocity omegaab = 3 rad/s and an angular acceleration alphaab = 5 rad/s2. determine the angular velocit...

question

Engineering, 14.09.2019 01:30

At the instant shown, the velocity of collar a is 0.4m/s to the right and the velocity of collar b is 1m/s to the left. determine (a) the angular velo...

question

Engineering, 14.09.2019 02:10

The condition of irrotationality for a two-dimensional flow is satisfied when rotation w everywhere is (less than — equal to — more than) zero....

question

Engineering, 14.09.2019 02:10

The flow of a real fluid has (more —less - same ) complexity of an ideal fluid, owing to the phenomena caused by the existence of (viscosity-pressure...

question

Engineering, 14.09.2019 02:10

In laminar now, fluid particles are constrained to motion in (parallel —perpendicular opposite) paths by the action of (temperature- viscosity —pressu...

question

Engineering, 14.09.2019 02:10

Which of the following is not a function of a plc programming device? a. to enter the user program b. to monitor the user program c. to execute the u...

question

Engineering, 14.09.2019 02:10

Acertain measurement is performed 50 times. the arithmetic mean reading is 7.163 ft., and the standard deviation is 0.01 ft. how many readings fall wi...

question

Engineering, 14.09.2019 02:10

Apolyimide photoresist requires 90 mj/cm^2 per micron of thickness to be developed properly. if a lamp provides 900 w/m, how long does it take to expo...

question

Engineering, 14.09.2019 02:10

Determine ixx for the cylinder with a concentarted circular hole. the mass of body is m...

question

Engineering, 14.09.2019 02:10

Two 14.5° pressure angle, mating, 5-pitch gears have 30 and 110 teeth. in practice, the gears are mounted at a center distance 0.7 inches greater than...

question

Engineering, 14.09.2019 02:10

The center distance of two spur gears that have 20° pressure angle and full-depth with diametral pitch of 8 teeth/in, is increased by 0.05 in over the...

question

Engineering, 14.09.2019 02:10

Two meshing 24-pitch, 25° pressure angle gears have n1-24 and n2 60 teeth. the in use center distance of the two gears is 0.16 inches larger than the...

question

Engineering, 14.09.2019 02:10

Batteries are used in a plc's processor to a. maintain data in nonvolatile memory when line power is removed from the processor. b. maintain data in v...

question

Engineering, 14.09.2019 02:10

Acomplex cmos fabrication process requires 25 masks a. what fraction of the dice must be good (i. e. what yield must be obtained) during each mask ste...

question

Engineering, 14.09.2019 02:10

Draw and label a typical true stress-strain curve for a ductile material....

question

Engineering, 14.09.2019 02:10

Draw and label a typical engineering stress-strain curve for a brittle material....

question

Engineering, 14.09.2019 02:10

Determine the length l of each of the slender rods of mass m/2 which must be centrally attached to the faces of the thin homogeneous disk of mass m in...

question

Engineering, 14.09.2019 02:10

Afour-stroke cycle engine delivers a torque of 437 ft-lb at the flywheel (output shaft) when the engine speed is 2100 rpm while using 514 hp of fuel e...

question

Engineering, 14.09.2019 02:10

It takes a man 12.5 hours to complete a 500-mile trip in his automobile, during which 18 gallons of gasoline are consumed. during this trip, the avera...

question

Engineering, 14.09.2019 02:10

For a motor purchased for a tank project, it claims that at 12v it produces 6000 rpm. this motor is attached to a 50: 1 gear reduction gearbox. the ou...

More questions: Mathematics Another questions

Questions on the website: 13722363