subject

Mathematics, 30.12.2020 06:20 nyceastcoast

Q = d / d+ n on a manufacturer's assembly line, d parts are found to be defective and n parts are nondefective. the formula above is used to calculate a quality-of-parts ratio. What is d expressed in terms of the other two variables? a. n / 1 - q
b. nq / 1 - q
c. n / q-1
d. nq / q-1

ansver

Answers: 1

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 17:30

Asailor is looking at a kite. if he is looking at the kite at an angle of elevation of 36and the distance from the boat to the point where the kite is directly overhead is 40 feet, how high is the kite?

Answers: 1

question

Mathematics, 22.06.2019 02:00

What number gives you a irrational number when added to 2/5

Answers: 1

question

Mathematics, 22.06.2019 05:30

Robert plans to make a box-and-whisker plot of the following set of data. 27, 14, 46, 38, 32, 18, 21 find the lower quartile, the median, and the upper quartile of the set? lower quartile: 19.5; median: 29.5; upper quartile: 42 lower quartile: 14; median: 27; upper quartile: 46 lower quartile: 18; median: 27; upper quartile: 38 lower quartile: 16; median: 29.5; upper quartile: 42

Answers: 1

question

Mathematics, 22.06.2019 05:30

Shane and abha earned a team badge that required their team to collect no less than 2000 cans for recycling. abha collected 178 more cans than shane did. write an inequality to determine the number of cans, s, that shane could have collected.

Answers: 2

You know the right answer?

Q = d / d+ n on a manufacturer's assembly line, d parts are found to be defective and n parts are no...

Questions

question

Mathematics, 11.07.2019 01:10

Carolina receives an allowance that is tied to completing her chores during the week. she starts off with an allowance of $20. she has five chores to...

question

Engineering, 11.07.2019 01:10

Water-to-water heat pumps are recently being employed to produce hot water, in-stead of gas water heaters. a water-to-water vapor compression heat pum...

question

Engineering, 11.07.2019 01:10

Which one of the following is not a planar defect? a)- twin boundary b)- interstitials c)- stacking fault d)- twist boundary...

question

Engineering, 11.07.2019 01:10

A0.002-m3 steel tank is rapidly filled with air for 10 s. the air enters the tank at 300 k with a mass flow rate of 0.00017 kg/s. the tank initially c...

question

Engineering, 11.07.2019 01:10

Draw neat diagrams showing three different kinds of cubic unit cells. which one of these ie least commonly observed in metals and why? how do line de...

question

Engineering, 11.07.2019 01:10

Which of the following statements about atomic vacancy sites in metals is incznrect a)- a vacancy represents the empty space in an otherwise cosed pac...

question

Engineering, 11.07.2019 01:10

Aheat engine operates between thermal reservoirs of 1000k and 400k. it receives heat at a rate of 200 kw and rejects it at a rate of 90 kw a)- what is...

question

Engineering, 11.07.2019 01:10

In what kind of diffusion processes do we use fick's i and il laws? explain all the parameters (c c(x, t), co, t, and x) shown in the diffusion curve...

question

Engineering, 11.07.2019 01:10

Acapacitance sensor consists of two overlapping plates separated by a small gap filled with either a dielectric material or a vacuum. capacitance is c...

question

Engineering, 11.07.2019 01:10

Across-flow air-to-water heat exchanger (both fluids unmixed) with an effectiveness of 0.65 is used to heat water (cp 4180 j/kg. k) with hot air (c 10...

question

Engineering, 11.07.2019 01:10

Determine the bending stress at the surface of a 3-in.-diameter shaft subjected to a bending moment of 3200 lb-ft....

question

Engineering, 11.07.2019 01:10

Consider a spent nuelear fuel rod of constant thermal conductivity k, perimeter p, length l, and uniform cross-sectional area ac. energy is released a...

question

Engineering, 11.07.2019 01:10

An ideal gas of butane in a piston-cylinder device is initially at 8a fahrenheit and 1 bar undergoes a thermodynamic cycle consisting of three process...

question

Engineering, 11.07.2019 01:10

Calculate the speed of a (i) 0.5-mev electron. ii) 25-mev electron. (b) how much greater than the rest mass is the mass of each of the energetic elect...

question

Engineering, 11.07.2019 01:10

1.0 kg of air at 300 k and 100 kpa (state 1) is slowly compressed in a piston cylinder (closed system). the compression process is an isothermal proce...

question

Engineering, 11.07.2019 01:10

A16-bit aid converter has a full-scale range+10 v. what is the resolution of this a/d in volts? if this a/d were used to measure temperature using a...

question

Engineering, 11.07.2019 01:10

List the different types of solar cells and their efficiency ranges...

question

Engineering, 11.07.2019 01:10

Assuming the following, what is the fill factor for the following solar cell? power=100w voc=30v isc=10a...

question

Engineering, 11.07.2019 01:10

Increasing temperature will reduce the corrosion rate. a)-true b)- false...

question

Engineering, 11.07.2019 01:10

The yield stress of a tension specimen machined from a 2-m wide by 0.6-cm thick copper sheet is 145 mpa. the sheet is rolled further with an applied t...

More questions: Mathematics Another questions

Questions on the website: 13722367