The area of a rectangle is found using the formula A = lw, where l is the length of the rectangle and w is the width. Multiply each pair of factors and express the area of each rectangle as a single polynomial in terms of x.
1 = 4x2 + 8; w = 2x2 – 3

step-by-step explanation:

equation

you are asked to write the equation

  expression = 0

using the given expression. when you do that, you have

  2x^2-2x-12 = 0

factoring

you can see that each of the coefficients is even, so a factor of 2 can be removed immediately.

  2(x^2 -x -6) = 0

if you multiply the binomials (x+a)(x+b), you get

  (x +a)(x +b) = x^2 +(a+b)x +ab

this tells you the coefficient of x is the sum of two factors of the constant term. here, that means -1 is the sum of two factors of -6. we want to know those factors so we can factor the trinomial.

  -6 = -1×6 = -2×3 = -3×2 = -6×1

the factor pair that sums to -1 is {-3, 2}, so our factorization is

  2(x -3)(x +2) = 0

solutions

the solutions to this equation are the values of x that make the product zero. a product is zero only when only of the factors of the product is zero. here, that means

  x - 3 = 0

  x = 3 . . . add 3 to both sides of the equation

or

  x +2 = 0

  x = -2 . . . add -2 to both sides of the equation

the solutions to the equation are x=3 or x=-2. both of these values of x satisfy the equation—they make it be true.

the expression (1.26)2t reveals the approximate rate of increases in the number of plants semiannually.

hope this : )

part a

answer: a reasonable domain is where n is a real number. so n can be between 0 and 10. both endpoints are included.

work shown:

n is the number of days after the experiment starts. the smallest n can be is n = 0 which means that 0 days have gone by, and we're at the start. to find out how large n should be, then replace f(n) with 16.13 and solve for n. use logarithms to isolate the exponent.

f(n) = 12*(1.03)^n

16.13 = 12*(1.03)^n

16.13/12 = (1.03)^n

1.34416666666667 = (1.03)^n

(1.03)^n = 1.34416666666667

log[ (1.03)^n ] = log[ 1.34416666666667 ]

n*log[ 1.03 ] = log[ 1.34416666666667 ]

n = log[ 1.34416666666667 ]/log[ 1.03 ]

n = 10.0062999823929

this rounds to n = 10 which is fairly close but not 100% perfect. so this is the largest n can be.

note: if you plug n = 10 into f(n), you'll get roughly 16.127 which rounds to 16.13 (this comes up again in part c)

=====================================

part b

answer: the y intercept is 12. it represents the starting height of the plant in cm.

work shown:

plug n = 0 into the f(n) function. simplify

f(n) = 12*(1.03)^n

f(0) = 12*(1.03)^0

f(0) = 12*(1)

f(0) = 12

on day n = 0, aka the starting point, the height f(n) is 12 cm

=====================================

part c

answer: the average rate of change is approximately 0.43061036458991 (round however you need to). this represents the average growth rate from day n = 3 to day n = 10. so the plant grew roughly 0.43 cm per day during this timespan, assuming you round to 2 decimal places.

work shown:

compute f(3)

f(n) = 12*(1.03)^n

f(3) = 12*(1.03)^3

f(3) = 13.112724 < we'll use this later

compute f(10)

f(n) = 12*(1.03)^n

f(10) = 12*(1.03)^10

f(10) = 16.1269965521294 < we'll use this later

now use the formula below with a = 3 and b = 10

aroc = average rate of change

aroc = [ f(b) - f(a) ]/[ b - a ]

aroc = [ f(10) - f(3) ]/[ 10 - 3 ]

aroc = (16.1269965521294 - 13.112724)/(10 - 3)

aroc = 3.0142725521294/7

aroc = 0.43061036458991

round this however you need to

note: the plant grew approximately 3.01 cm over 7 days, so roughly 0.43 cm per day is the average growth rate (if you were to round to 2 decimal places).

.

step-by-step explanation:

.