subject

Mathematics, 31.08.2020 19:01 fraven1819

What is the perimeter of the rectangle

What is the perimeter of the rectangle

ansver

Answers: 2

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 15:50

Name the most appropriate metric unit for each measurement

Answers: 3

question

Mathematics, 21.06.2019 18:00

Solve this system of equations. 12x − 18y = 27 4x − 6y = 10

Answers: 1

question

Mathematics, 21.06.2019 18:00

What percent of the circle below is shaded?

Answers: 1

question

Mathematics, 22.06.2019 06:20

Jace didn’t pay his previous month’s credit card bill in full. this month’s bill shows a finance charge of $35.13. jeremy calculates the average daily balance in the new bill to be $2,342.15. what is the monthly percentage rate on the card? a. 1.5% b. 1.82% c. 14.9% d. 18.0%

Answers: 1

You know the right answer?

What is the perimeter of the rectangle
...

Questions

question

Engineering, 29.09.2019 01:10

Aface milling operation is to be performed on cast iron. tool diameter is 5 inches, w = 2 inches, part length = 8 inches, depth of cut = 0.012 inches,...

question

Engineering, 29.09.2019 01:10

A2.3-in-diameter steel rod 3 ft long is used between two immovable (rigid) walls. the rod is welded to the two walls at each of its two ends. the ambi...

question

Engineering, 29.09.2019 01:10

Alow-speed cessna 150 flying at 5,000 ft pressure altitude has an indicated airspeed of 250 ft/s. if the outside temperature is 30°f and there is a 50...

question

Engineering, 29.09.2019 01:10

Electric power is to be generated by installing a hydraulic turbine-generator at a site 120 m below the free surface of a large water reservoir that c...

question

Engineering, 29.09.2019 01:10

A0.66 ft steel bar undergoes a stretch of 0.75 in in an axial direction. what is the strain? use three significant figures (four if your the first no...

question

Engineering, 29.09.2019 01:10

Calculate the local reynolds number at a point 0.1 ft aft of the leading edge of a wing, which is being tested at sea level, standard day conditions,...

question

Engineering, 29.09.2019 01:10

Ametallic rod with a diameter of 2.8 in and a modulus of 31.2 x 10^6 psi is elastically deformed to a tensile strain of 2.80 x 10^-3 in/in. calculate...

question

Engineering, 29.09.2019 01:10

Aboiler is operating at a pressure of 7,000kpa and steam outlet temperature is 600c, what is the heat per kilogram of steam required to convert the wa...

question

Engineering, 29.09.2019 01:10

Determine displacement (in) of a 1.28 in diameter steel bar, which is 50 ft long under a force of 21,672 lb if elasticity modulus is 30 x 10^6 psi. ma...

question

Engineering, 29.09.2019 01:10

A10.2 mm diameter steel circular rod is subjected to a tensile load that reduces its cross- sectional area to 52.7 mm^2. determine rod's percent ducti...

question

Engineering, 29.09.2019 01:10

If the bending moment (m) is 4,176 ft-lb and the beam is an 1 beam, calculate the bending stress (psi) developed at a point with a distance of c = 3.9...

question

Engineering, 29.09.2019 01:10

Find the stress (psi) in a rod with a 0.68 in diameter caused by a 528 lb axial load....

question

Engineering, 29.09.2019 01:10

Aspark ignition engine is to be modeled using fluid, air, is at 95 kpa and 290 k before compression. the compression ratio is 9 and the maximum temper...

question

Engineering, 29.09.2019 01:10

Technican a says that the transmission hydraulic pump operates only when the vehicle is in motion. technician b says that the transmission hydraulic p...

question

History, 29.09.2019 01:10

The idea within the work place of "let those fist to survive, survive," and if the employee gets hurt it is their fault and not their working conditio...

question

Mathematics, 29.09.2019 01:10

Travis is fishing from a small boat. his fishing hook is 7 meters below him, and a fish is swimming at the same depth as the hook, 24 meters away. how...

question

Engineering, 29.09.2019 01:10

Asolid steel bar of circular cross section has diameter d = 1.5 in., length l = 54 in., and shear modulus of elasticity g = 11.5 x 10^6 psi. the bar i...

question

Engineering, 29.09.2019 01:10

Technician a says shift solenoids are used on some transmission to control upshoft and down shift. technician b says governor pressure is used on some...

question

Biology, 29.09.2019 01:10

What are the layers of the sun, starting from the center and moving outward? core, convective zone, radiative zone, and photosphere core, radiative z...

question

Mathematics, 29.09.2019 01:10

Who knows the answer for this one ?...

More questions: Mathematics Another questions

Questions on the website: 13722359