Which transformations are needed to change the parent cosine function to the cosine function below? on a coordinate plane, a curve crosses the y-axis at y = 1. it has a maximum of 1 and a minimum of negative 3. it goes through 2 cycles at 2 pi.

the range of a function is the range of y-values for which it is defined, or exists. given that we are only looking at the y-values, we can already discount the first two answers as they deal with the domain of the function (range of x-values).

now, what we need to do is find the smallest and highest y-values for which the function is defined. if you'd like, you could take a ruler and start at the very bottom of the graph, find the lowest point, then move the ruler higher and higher until you reach the highest point. doing so either in your head or with an actual ruler, we can see that the lowest y-value is -5 and the highest y-value is -1.

the question now remains as to whether they are included in the range (fourth answer) or excluded (third answer). the key here is to recognise whether they are marked with an open or a closed circle. since both (-2, -5) and (2, -1) are marked with a closed circle, they are points that exist on the graph and are thus included in the range (note that if they were marked with an open circle like (4, -2) then that would signify that there is a break in the graph at that point).

thus, the fourth answer, (y | -5 ≤ y ≤ -1), is correct.

also note that usually it is good practice to scan your eye inbetween the highest and lowest point for any breaks in the graph - we do have one here at (4, -2), however -2 is still included in the range because there is another point that is included in the graph with the same y-value, ie. point (1, -2).

i hope that but if you require any further explanation don't hesitate to comment below.

8 2/3 is the answer

step-by-step explanation: just use a calculator

answer: ratio of volume of cone (with 3 times the height and equal diameter) to volume of cylinder is 2 to 1. the value of π is not used.

step-by-step explanation:

radius is diameter/2 = 4.

area of circle is π r^2.

volume of cylinder is height × area of base = hπr^2 = 3(4^2) π = 48π cubic inches.

not knowing the formula for volume of cone, i calculate it using calculus (which is for calculating things).

volume of cone is integral 0 to h area(y) dy. area(y) is π r(y)^2. r(y) runs r to zero as y runs zero to h, r(0) = r, r(h) = 0.

r(y) = r - r/h y

area(y) = π (r - r/h y)^2 = π (r^2 - 2r^2y/h + r^2y^2/h^2) = π r^2(1-2y/h+y^2/h^2)

antiderivative area(y) = π r^2 (y-y^2/h+y^3/(3h^2))

integral 0 to h = π r^2(h-h^2/h+h^3/(3h^2) - (0)) = π r^2(h - h + h/3) = π r^2(h/3) = π/3 r^2 h

volume of this cone is π/3(4^2)18 cubic inches.

= 6 16 π = 96π cubic inches.

cone has twice the volume, 96/48.

cone height is 6 times the cylinder.

ratio of volume formula: π r^2 cancels.

cone over cylinder ratio is 6h/3 to h, 2 to 1.

pakistan's principal natural resources are arable land and water. about 25% of pakistan's agriculture accounts for about 21% [1] of gdp and employs about 43% of the labour force. in pakistan, the most agricultural province is punjab where wheat and cotton are the most grown.