History, 17.02.2021 21:20 Deagon4434

Of all the hardships faced by people who went west what do you think was the worst

Answers: 1

Show answers

Another question on History

History, 21.06.2019 14:30

At the time if the glorious revolution and the writing if the english bill of rights, americans

Answers: 2

Answer

History, 21.06.2019 15:30

How did the economy in the 20’s lead to the florida land boom.

Answers: 1

Answer

History, 22.06.2019 01:30

Which physical feature minimizes population density in northern africa?

Answers: 1

Answer

History, 22.06.2019 07:00

With state which alliance promoted goals and protection of the united states and which alliance promoted goals and protection of the soviet union. site and explain evidence from each primary source to support your answers.

Answers: 1

Answer

You know the right answer?

Of all the hardships faced by people who went west what do you think was the worst
...

Questions

Engineering, 26.07.2019 18:20

A0.65 lb, 20 inch radius hula hoop is thrown forward with a velocity at the center of gravity of vg = 6 ft/s. however, the hula hoop initially has a b...

Engineering, 26.07.2019 18:20

High pressure oil is usually applied to journal bearing a)-between the top of the journal and the bearing and the bearing b)-between the bottom of the...

Engineering, 26.07.2019 18:20

Roller bearings are commonly referred to as "antifriction" bearings because: a) there is no measurable friction in the rolling members b) there is le...

Engineering, 26.07.2019 18:20

A90 wt% ag-10 wt% cu alloy is heated to a temperature within the b + liquid phase region. if the composition of the liquid phase is 85 wt% ag, determi...

Engineering, 26.07.2019 18:20

Poor resistance to scoring in journal bearings is called: a) fatigue resistance b) cohesive wear c) adhesive wear d) abrasive wear...

Engineering, 26.07.2019 18:20

The material flow in lean manufacturing a. depends on automation. b. is "pulled forward" due to customer demand. c. depends on the availability of raw...

Engineering, 26.07.2019 18:20

Which bearing material is classed as being self-lubricating? a) teflon b) babbitt c) bronze d) aluminum...

Engineering, 26.07.2019 18:20

Athin silicon chip and an 8mm thick aluminum substrate (k = 240w/m. k) are separated by 0.025mm thick epoxy joint. the thermal contact resistance betw...

Engineering, 26.07.2019 18:20

Seizures in journal bearings usually occur because of a) localized hot spots b) poor thermal conductivity c) poor bearing fit d) all of the above....

Engineering, 26.07.2019 18:20

Ball and roller bearings are classified according to:...

Engineering, 26.07.2019 18:20

Apyrometer can be used to determine the recommended pouring temperature of the babbitt. a) true - b) false...

Engineering, 26.07.2019 18:20

For a copper-silver alloy of composition 30 wt% ag-70 wt% cu and at 775°c (1048 k), do the following: (a) determine the mass fractions of α and β pha...

Engineering, 26.07.2019 18:20

Which of the following statements is true of fixed-automation devices? a. they can't be used in automation on flow lines. b. they can be easily chang...

Engineering, 26.07.2019 18:20

Which method of lubrication uses centrifugal force to distribute the oil to the bearing? a) oil ring b) splash fed c) pressure lubrication d) oil bat...

Engineering, 26.07.2019 18:20

Which of the following statements is/are true? (a). engineers apply tolerances to part dimensions to reduce the amount of variation that occurs durin...

Engineering, 26.07.2019 18:20

An automobile tire has a volume 81.900 cm^3 and contains air and a gauge pressure of 2.07x 10^5n/m^2 when the temperature is 0°c. what is the gauge pr...

Engineering, 26.07.2019 18:20

A300ft long section of a steam pipe whose diameter is 4in passes through an open space at 0°f. the average temperature of the outer surface of the pip...

Engineering, 26.07.2019 18:20

Is it possible to have a copper-nickel alloy that, at equilibrium, consists of a liquid phase of composition 20 wt% ni-80 wt% cu and also an a phase o...

Engineering, 26.07.2019 18:20

When can one assume that a mass can be approximated as a particle?...

Engineering, 26.07.2019 18:20

The exact theoretical size from which the limits of mating parts are assigned when tolerancing is a. basic size b. bulk size c. perfect size d. preci...

More questions: History Another questions

Of all the hardships faced by people who went west what do you think was the worst ​

Answers

Another question on History

Of all the hardships faced by people who went west what do you think was the worst