![subject](/tpl/images/cats/User.png)
Engineering, 18.08.2021 15:50 jbcupcake
A concentric tube arrangement, for which the inner and outerdiameters are 80mm and 100mm, respectively, is used to remove heatfrom a biochemical reaction occurring in a 1-m-long settlingtank. Heat is generated within the tank at a rate of 10^5W/m^3, and water is supplied to the annular region at a rate of 0.2kg/s.
Required:
Determine the inlet temperature of the supply water that willmaintain an average tank surface temperature of 37 degrees C. Assume fully developed flow and thermal conditions. Is this assumption reasonable?
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Inadequate stores control is not an obstacle to effective work order system. (clo4) a)-true b)-false
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
An engine runs on the ideal diesel cycle. the cycle has a compression ratio of 20 and a cutoff ratio of 2. the highest temperature in the cycle is 1200 k. if the heat into the system is 300 kj/kg of working fluid and using variable specific heats determine the work produced per mass of working fluid
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
How much power could a wind turbine produce if it had the following specifications? cp = 0.45 -d=1.2kg/m3 d=50m v 5m/s
Answers: 2
You know the right answer?
A concentric tube arrangement, for which the inner and outerdiameters are 80mm and 100mm, respective...
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 15.01.2021 20:30
![question](/tpl/images/cats/fizika.png)
Physics, 15.01.2021 20:30
![question](/tpl/images/cats/mat.png)
Mathematics, 15.01.2021 20:30
![question](/tpl/images/cats/geografiya.png)
Geography, 15.01.2021 20:30
![question](/tpl/images/cats/mat.png)
Mathematics, 15.01.2021 20:30
![question](/tpl/images/cats/mat.png)
Mathematics, 15.01.2021 20:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 15.01.2021 20:30
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 15.01.2021 20:30
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 15.01.2021 20:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/User.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 15.01.2021 20:30
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 15.01.2021 20:30