Engineering, 19.02.2021 15:20 laurenlay156

Can someone teach me how to find all valid minterms of any given truth table?

Answers: 2

Show answers

Answers

Answer from: gabby77778

Explanation:

A minterm is a product of variables, in which each variable appears exactly once, either complemented or not. When a truth table is represented in a sum of products form, there is one minterm for each line in the table for which the output is True (1).

Suppose I have a truth table as follows, with inputs A, B and output Z.

AB Z

00 1

01 0

10 1

11 0

When I write the minterms, I use a complemented variable where the input is 0, and an uncomplemented variable where the input is 1. The minterm is expressed as a product of those variables.

Here, there are 2 lines in the table with outputs Z=1. The input conditions AB for those outputs are 00 and 10, so the corresponding minterms are A'B' and AB', where the apostrophe indicates the variable is complemented.

This table is then represented by the sum of products ...

Z = A'B' + AB'

You have all of the valid minterms when you have one for each line of the table where the output is 1.

Comment on truth table representation

Truth tables can be represented a number of ways. A nice representation for the purpose of identifying minterms is a list of the output for every possible combination of inputs. We have used that form above.

Sometimes, you may see minterms listed as decimal numbers in the range of 0 to 2^n -1 when there are n input variables. Then, the minterms are developed from the binary equivalents of those decimal numbers.

Example:

Logic with 4 input variables has minterms 7, 8, and 15. The binary equivalents of these numbers are 0111, 1000, 1111. The corresponding minterms (for inputs a, b, c, d) are a'bcd + ab'c'd' + abcd = z. Three numbers are listed, so we know we have all of the valid minterms when we have three corresponding minterms.

Additional comment

In some cases, outputs will be listed as "don't care." Another set of minterms can be generated for the don't cares. These can be used in the logic minimization process.

Answer from: Quest

answer:

explanation:

Answer from: Quest

answer: hi

explanation:

Another question on Engineering

Engineering, 04.07.2019 18:10

Water at 70°f and streams enter the mixing chamber at the same mass flow rate, determine the temperature and the quality of the exiting stream. 0 psia is heated in a chamber by mixing it with saturated water vapor at 20 psia. if both streams enters the mixing chamber at the same mass flow rate, determine the temperature and the quality of the existing system.

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Which of the following ziegler nichols tuning methods the response of the controller to a step input should exhibit an s-shaped curve? a)-open loop mode b)-closed loop mode c)-both modes (open & closed) d)-none of the modes (open & closed)

Answers: 3

Answer

Engineering, 04.07.2019 19:20

At steady state, air at 200 kpa, 325 k, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. the inlet cross-sectional area is 6 cm2. at the duct exit, the pressure of the air is 100 kpa and the velocity is 250 m/s. neglecting potential energy effects and modeling air as an 1.008 kj/kg k, determine ideal gas with constant cp = (a) the velocity of the air at the inlet, in m/s. (b) the temperature of the air at the exit, in k. (c) the exit cross-sectional area, in cm2

Answers: 2

Answer

Engineering, 05.07.2019 19:10

Tech a says never use a water hose to clean up dust after a repair. tech b says never use a floor scrubber to clean up dust after repairs. who is correct?