![subject](/tpl/images/cats/User.png)
Engineering, 15.12.2020 16:20 crowntinyy3408
The flow meter installed in the piping system measures the mass flow rate. Assume that the flow meter has a 0.5-in-diameter, square-edged orifice plate is used to meter the steady flow of 16C water through a 1.0-in pipe. Flange taps are used and the pressure drop measured is 50 cm Hg. Determine the air volume flow rate through the piping system. The specific gravity of mercury is 13.5.
![ansver](/tpl/images/cats/User.png)
Answers: 3
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
What difference(s) did you notice using a pneumatic circuit over hydraulic circuit.explain why the pneumatic piston stumbles when it hits an obstacle.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
If a particle moves along a path such that r : (3 sin t) m and ? : 2t rad, where t is in seconds. what is the particle's acceleration in m/s in 4 seconds? a)- 16.43 b)- 16.29 c)- 15.21 d)- 13.79
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.
Answers: 1
You know the right answer?
The flow meter installed in the piping system measures the mass flow rate. Assume that the flow mete...
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 23.07.2019 19:00
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/fizika.png)
Physics, 23.07.2019 19:00
![question](/tpl/images/cats/himiya.png)
Chemistry, 23.07.2019 19:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 23.07.2019 19:00
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/istoriya.png)
History, 23.07.2019 19:00
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 23.07.2019 19:00
![question](/tpl/images/cats/ap.png)
Advanced Placement (AP), 23.07.2019 19:00
![question](/tpl/images/cats/himiya.png)
Chemistry, 23.07.2019 19:00
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
History, 23.07.2019 19:00
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 23.07.2019 19:00