In the equation, Q = mC(T2 – T1), Q is the amount of
needed, m is the
, and T1 and T2 are th...
![subject](/tpl/images/cats/User.png)
Engineering, 08.12.2020 22:50 tporter00
In the equation, Q = mC(T2 – T1), Q is the amount of
needed, m is the
, and T1 and T2 are the initial and final temperatures. The higher the
C, the more energy you need to produce a given temperature change in a material.
![ansver](/tpl/images/cats/User.png)
Answers: 3
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Give heat transfer applications for the following, (i) gas turbines (propulsion) ) gas turbines (power generation). (iii) steam turbines. (iv) combined heat and power (chp). (v) automotive engines
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Water in a partially filled large tank is to be supplied to the roof top, which is 8 m above the water level in the tank, through a 2.2-cm-internal-diameter pipe by maintaining a constant air pressure of 300 kpa (gage) in the tank. if the head loss in the piping is 2 m of water, determine the discharge rate of the supply of water to the roof top in liters per second.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
Afoot bridge is made as a simple deck, 4 m long, with a cross section 2 m (wide) and 20 cm thick, and made of wood. the deck is supported at the two ends. the maximum load allowable on the bridge is 10 tons, provided it is uniformly distributed on the deck. to sense this load, a strain gauge is placed at the center of the bridge and its resistance is monitored. if the sensor has a nominal resistance of 350 s2 and a gauge factor of 3.6, what is the reading of the strain gauge at maximum load? the modulus of elasticity for the wood used in the construction is 10 gpa.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
Aplate of dimensions 3 m x 3 m is placed 0.37 mm apart from a fixed plate. the plate requires a force of 2n to move at speed of 45 cm/s. evaluate the viscosity of the fluid in between the plates
Answers: 3
You know the right answer?
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
English, 05.03.2020 07:50
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/User.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
English, 05.03.2020 07:51
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 05.03.2020 07:51
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 05.03.2020 07:53