⣴⣿⡿⠛⠉⠙⠛⠛⠛⠛⠻⢿⣿⣷⣤⡀ ⠀⠀⠀⠀⠀⠀⠀⠀⣼⣿⠋⠀⠀⠀⠀⠀⠀ ⠀⢀⣀⣀⠈⢻⣿⣿⡄

⠀⠀⠀⠀⠀⠀⠀⣸⣿⡏⠀⠀⠀⣠⣶⣾⣿⣿⣿⠿⠿⠿⢿⣿⣿⣿⣄

⠀⠀⠀⠀⠀⠀⠀⣿⣿⠁⠀⠀⢰⣿⣿⣯⠁⠀⠀⠀⠀⠀⠀⠀⠈⠙⢿⣷⡄

⠀⠀⣀⣤⣴⣶⣶⣿⡟⠀⠀⠀⢸⣿⣿⣿⣆⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⣿⣷

⠀⢰⣿⡟⠋⠉⣹⣿⡇⠀⠀⠀⠘⣿⣿⣿⣿⣷⣦⣤⣤⣤⣶⣶⣶⣶⣿⣿⣿

⠀⢸⣿⡇⠀⠀⣿⣿⡇⠀⠀⠀⠀⠹⣿⣿⣿⣿⣿⣿⣿⣿⣿⣿⣿⣿⣿⡿⠃

⠀⣸⣿⡇⠀⠀⣿⣿⡇⠀⠀⠀⠀⠀⠉⠻⠿⣿⣿⣿⣿⡿⠿⠿⠛⢻⣿⡇

⠀⣿⣿⠁⠀⠀⣿⣿⡇⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⢸⣿⣧

⠀⣿⣿⠀⠀⠀⣿⣿⡇⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⢸⣿⣿

⠀⣿⣿⠀⠀⠀⣿⣿⡇⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⢸⣿⣿

⠀⢿⣿⡆⠀⠀⣿⣿⡇⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⢸⣿⡇

⠀⠸⣿⣧⡀⠀⣿⣿⡇⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⠀⣿⣿⠃

⠀⠀⠛⢿⣿⣿⣿⣿⣇⠀⠀⠀⠀⠀⣰⣿⣿⣷⣶⣶⣶⣶⠶⢠⣿⣿

⠀⠀⠀⠀⠀⠀⠀⣿⣿⠀⠀⠀⠀⠀⣿⣿⡇⠀⣽⣿⡏⠁⠀⠀⢸⣿⡇

⠀⠀⠀⠀⠀⠀⠀⣿⣿⠀⠀⠀⠀⠀⣿⣿⡇⠀⢹⣿⡆⠀⠀⠀⣸⣿⠇

⠀⠀⠀⠀⠀⠀⠀⢿⣿⣦⣄⣀⣠⣴⣿⣿⠁⠀⠻⣿⣿⣿⣿⡿⠏ Whites sus

⠀⠀⠀⠀⠀⠀⠀⠈⠛⠻⠿⠿⠿⠿⠋⠁

A3-mm-thick panel of aluminum alloy (k 177 w/m-k, c 875 j/kg-k and ? = 2770 kg/m) is finished on both sides with an epoxy coating that must be cured at or above t,-150°c for at least 5 min. the production line for the curing operation involves two steps: (1) heating in a large oven with air at ts,0-175°c and a convection coefficient of h, 40 w/m2. k, and (2) cooling in a large chamber with air at 25°c and a con- vection coefficient of he 10 w/m2.k. the heating portion of the process is conducted over a time interval te which exceeds the ime required to reach 150°c by 5 min (h = r + 300 s). the coating has an emissivity of ? = 0.8, and the temperatures of the oven and chamber walls are 175 and 25°c, respectively. if the panel is placed in the oven at an initial temperature of 25°c and removed from the chamber at a safe-to-touch tempera ture of 37°c, what is the total elapsed time for the two-step curing operation?

Acompressor compresses a gas, a pump compresses a liquid. for a given pressure ratio, why does it take more work to compress a gas in a compressor than a liquid in a pump? a)- for a given pressure ratio the average specific volume for a gas is much higher than the average specific volume for a liquid. b)- there is no difference. the only difference is the amount of heat generated (not work) c)- for a given pressure ratio the average volurge for a gas is much higher than the average volume for a liquid. d)-there is no difference

Two slings are used to lift a girder of length l and uniform weight per unit length. what is the best position for the slings if the bending moment due to the weight of the girder is to be kept to a minimum?