Who does the narrator blame for the loss of her job as editor-in-chief?
see if i care readwor...
![subject](/tpl/images/cats/User.png)
Engineering, 16.10.2020 19:01 chloe9869
Who does the narrator blame for the loss of her job as editor-in-chief?
see if i care readworks
![ansver](/tpl/images/cats/User.png)
Answers: 3
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Shafts are machine elements that are used to a) carry axial loads b) direct shear loads c) transmit power d) rotate at constant speed e) none of the above circular and square shafts subjected to the same torque under the same circum behave a) the same way b) almost the same way
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Awall of 0.5m thickness is to be constructed from a material which has average thermal conductivity of 1.4 w/mk. the wall is to be insulated with a material having an average thermal conductivity of 0.35 w/mk so that heat loss per square meter shall not exceed 1450 w. assume inner wall surface temperature of 1200°c and outer surface temperature of the insulation to be 15°c. calculate the thickness of insulation required.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20
At steady state, air at 200 kpa, 325 k, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. the inlet cross-sectional area is 6 cm2. at the duct exit, the pressure of the air is 100 kpa and the velocity is 250 m/s. neglecting potential energy effects and modeling air as an 1.008 kj/kg k, determine ideal gas with constant cp = (a) the velocity of the air at the inlet, in m/s. (b) the temperature of the air at the exit, in k. (c) the exit cross-sectional area, in cm2
Answers: 2
You know the right answer?
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 23.10.2020 17:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 23.10.2020 17:00
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 23.10.2020 17:00
![question](/tpl/images/cats/mat.png)
Mathematics, 23.10.2020 17:00
![question](/tpl/images/cats/en.png)
English, 23.10.2020 17:00
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/geografiya.png)
Geography, 23.10.2020 17:00
![question](/tpl/images/cats/mat.png)
Mathematics, 23.10.2020 17:00
![question](/tpl/images/cats/es.png)
Spanish, 23.10.2020 17:00
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 23.10.2020 17:00
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 23.10.2020 17:00