subject
Engineering, 05.05.2020 04:26 bryan519688

The undisturbed soil at given borrow pit is found to have the following property:
w = 15%; y = 19.1 kN/m^3; Gs = 270
The soil from this borrow pit is to be used to construct a rolled fill having a finished volume of 38, 500 m^3. The soil is excavated by means of a shovel and dumped onto trucks saving a capacity of 4 00 m^3 each. When loaded to capacity, these trucks are found to contain, on the average, a net weight of toil and water equal to 72.7 kN
In the construction process. the trucks dump their load on the fill and the materials spread and broken up, after which a sprinkler adds water until the moisture content is equal to 18%. The soil and water are thoroughly mixed by a disc (or similar equipment) and then compacted until the dry unit weight is equal to 17.3 kN/m^3.
1. Assuming that each load is a full capacity load, how many truckloads are required to construct the fill?
2. How many liters of water will have to be added per truck load, assuming that the moisture tots by evaporation during excavation, haulage, and handling it negligible?

ansver
Answers: 2

Another question on Engineering

question
Engineering, 03.07.2019 14:10
Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.
Answers: 3
question
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
question
Engineering, 04.07.2019 18:10
Draw the engineering stress-strain curve for (a) bcc; (b) fcc metals and mark important points.
Answers: 1
question
Engineering, 04.07.2019 18:10
Awall of 0.5m thickness is to be constructed from a material which has average thermal conductivity of 1.4 w/mk. the wall is to be insulated with a material having an average thermal conductivity of 0.35 w/mk so that heat loss per square meter shall not exceed 1450 w. assume inner wall surface temperature of 1200°c and outer surface temperature of the insulation to be 15°c. calculate the thickness of insulation required.
Answers: 3
You know the right answer?
The undisturbed soil at given borrow pit is found to have the following property:
w = 15%; y...
Questions
question
Mathematics, 24.08.2021 03:40
question
Arts, 24.08.2021 03:40
question
Mathematics, 24.08.2021 03:40
question
Mathematics, 24.08.2021 03:40
question
Mathematics, 24.08.2021 03:40
Questions on the website: 13722361