subject
Engineering, 24.04.2020 16:24 treypickich14

From 2011-2015, California experienced an extreme drought. According to some paleoclimatologists, this drought was the most severe in the past 1200 years. Because water use for thermoelectric power generation is one of the largest uses of water world-wide, one means of reducing water use in California is shifting electricity generation to systems that consume less water. Although California imports much of the electricity it uses from other states, there is still a substantial amount of electricity generation that is done in-state, and this offers opportunities for water conservation.
a) Using the data provided in the Table below, estimate total water usage associated with electricity generation in California. Identify the type of electricity generation that uses the most water per MWhr and the type of electricity generation that uses the largest total amount of water.
b) If all electricity generation in California were to switch to natural gas and the water intensity of electricity generation (I water/MWh) remained the same, how much would water usage be reduced?
c) If the average municipal water use is 100 gal per person per day (36,500 gal/yr), how many people could be provided with water with the savings identified in part b? (1 gal = 3.81)
Fuel source Water used in extracting fuel Water used in generating electricity Electricity generated in California
- (liters of water per MWhr of elecetricity generated) (liters of water per MWhr of elecetricity generated) (MWhr)
Natural gas 24 737 76,082,000
Coal 96 1895 3,692,000
Nuclear 212 1817 36,586,000
Wind 0 4 2,418,000
Thermal Solar Source: 0 3975 681,000

ansver
Answers: 2

Another question on Engineering

question
Engineering, 04.07.2019 18:10
Which of the following ziegler nichols tuning methods the response of the controller to a step input should exhibit an s-shaped curve? a)-open loop mode b)-closed loop mode c)-both modes (open & closed) d)-none of the modes (open & closed)
Answers: 3
question
Engineering, 04.07.2019 18:10
Machinery that is a key part of the process and without which the plant or process cannot function is classifed as: (clo4) a)-critical machinery b)-essential machinery c)-general purpose machinery d)-none of the specified options.
Answers: 1
question
Engineering, 04.07.2019 18:20
Asolid cylinder is concentric with a straight pipe. the cylinder is 0.5 m long and has an outside diameter of 8 cm. the pipe has an inside diameter of 8.5 cm. the annulus between the cylinder ad the pipe contains stationary oil. the oil has a specific gravity of 0.92 and a kinematic viscosity of 5.57 x 10-4 m2/s. most nearly, what is the force needed to move the cylinder along the pipe at a constant velocity of 1 m/s?
Answers: 3
question
Engineering, 04.07.2019 19:20
Determine the time of the day and month of the year at which the peak sensible cooling load occurs for a top floor, north-eastern corner room of an office building in durban for the following conditions: floor area: 8 x 8 x 3 m east and north walls: 115 mm face brick (outside), 20 mm air space, 115 mm ordinary brick (inside) with 15 mm plaster roof construction: suspended plasterboard ceiling, 450 mm air space, 150 mm concrete, 75mm screed, waterproofing no heat transfer across other surfaces window area 3x 1,5 m high in north wall only. ordinary glass with venetian blinds. lights and occupants : from 07: 00 to 18: 00 average light density: 25 w/m2 number of occupants : 5 seated, light office work room temperature 24°c
Answers: 3
You know the right answer?
From 2011-2015, California experienced an extreme drought. According to some paleoclimatologists, th...
Questions
question
Mathematics, 10.03.2020 04:05
question
English, 10.03.2020 04:05
Questions on the website: 13722367