![subject](/tpl/images/cats/User.png)
Engineering, 17.04.2020 02:14 dani2997
Air at 10 C enters a 12-cm-diameter and 5-m-long pipe at a rate of 0.065 kg=s. The inner surface of the pipe has a roughness of 0.22 mm, and the pipe is nearly isothermal at 50 C. Determine the rate of heat transfer to air using the Nusselt number relation given by (a) Eq. 19{79 and (b) Eq. 19{84. Evaluate air properties at a bulk mean temperature of 20 C. Is this a good assumption?
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Asingle-geared blanking press has a stroke of 200 mm and a rated capacity of 320 kn. a cam driven ram is assumed to be capable of delivering the full press load at constant force during the last 15 percent of a constant-velocity stroke. the camshaft has an average speed of 90 rev/min and is geared to the flywheel shaft at a 6: 1 ratio. the total work done is to include an allowance of 16 percent for friction a) estimate the maximum energy fluctuation b) find the rim weight for an effective diameter of 1.2 m and a coefficient of speed fluctuation of 0.10
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Which one from below is not one of the reasons of planning failures? (clo3) a)-planner is careless. b-planner spend less time in the field but more time on the desk c)-planner is not qualified d)-planner does not have sufficient time to properly plan
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Awall of 0.5m thickness is to be constructed from a material which has average thermal conductivity of 1.4 w/mk. the wall is to be insulated with a material having an average thermal conductivity of 0.35 w/mk so that heat loss per square meter shall not exceed 1450 w. assume inner wall surface temperature of 1200°c and outer surface temperature of the insulation to be 15°c. calculate the thickness of insulation required.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
What are the major differences between injection molding and extrusion?
Answers: 2
You know the right answer?
Air at 10 C enters a 12-cm-diameter and 5-m-long pipe at a rate of 0.065 kg=s. The inner surface of...
Questions
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 30.12.2019 23:31
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 30.12.2019 23:31
![question](/tpl/images/cats/mat.png)
Mathematics, 30.12.2019 23:31