Engineering, 14.04.2020 23:01 runaway173

Convection ovens operate on the principle of inducing forced convection inside the oven chamber with a fan. A small cake is to be baked in an oven when the con- vection feature is disabled. For this situation, the free convection coefficient associated with the cake and its Steel sheet Concrete pad Ts, s Tb Ts Tsur Vs Pelec t s Lo ε Air T[infinity], h , 56 Chapter 1 ! Introduction CH001.qxd 2/24/11 12:03 PM Page 56 pan is hfr ! 3 W/m2 ! K. The oven air and wall are at temperatures T! ! Tsur ! 180)C. Determine the heat flux delivered to the cake pan and cake batter when they are initially inserted into the oven and are at a tem- perature of Ti ! 24)C. If the convection feature is acti- vated, the forced convection heat transfer coefficient is hfo ! 27 W/m2 ! K. What is the heat flux at the batter or pan surface when the oven is operated in the convection mode? Assume a value of 0.97 for the emissivity of the cake batter and pan.

Answers: 3

Show answers

Answers

Answer from: bethzabezarahi

complete question:

attached

2356.11 W/m^2

6100.11 W/m^2

Explanation:

Assumptions:

1. Steady-state conditions.

2. The cake is placed in a large surrounding.

3. Heat flux delivered to the cake is due to convection and radiation.

Case 1

Since convection feature is disabled the mode of heat transfer associated with this situation is through free convection and radiation.

q''(free) = [q''(free convection+q''(radiation) ]W/m^2

= h_free(T_infinty - T_i) + εσ(T_air^4 - T_i^4)

= 3 W/m^2K(180°C - 24°C) + 0.97*5.67*10^-8*[(180+273K)^4 -

(24+273K)^4 ]

= 468 +1881.11

= 2356.11 W/m^2

Case 2

Since convection feature is enabled or activated the mode of heat transfer associated with this situation is through forced convection and radiation.

q''(free) = [q''(forced convection+q''(radiation) ]W/m^2

= h_forced(T_infinty - T_i) + εσ(T_air^4 - T_i^4)

= 27 W/m^2K(180°C - 24°C) + 0.97*5.67*10^-8*[(180+273K)^4 -

(24+273K)^4 ]

= 4212 +1881.11

= 6100.11 W/m^2

1. The total heat flux is is 2.58 times higher when the convection feature is activated. Therefore the cake will bake faster during this condition.

2. The contribution of convection heat flux under natural(free) convection is very low as compared to the contribution during forced convection.

3. The heat transfer due to radiation is same in both the cases.

4. Only 19.9 % of the total heat flux is contributed by free convection in the first case.

5. In the second case 69 % of the total heat flux is contributed by forced convection.

Convection ovens operate on the principle of inducing forced convection inside the oven chamber with

Answer from: Quest

D) pirates hope it ..

Answer from: Quest

Because if a good speech is delivered badly it can bore the audience, confuse them, or make them distrust the speakeri think they all come back to this one, except that last answer because that is false. if your audience starts making fun of you or gets distracted it is because they are either bored, confused or distrust you.

Another question on Engineering

Engineering, 04.07.2019 18:10

Adouble-strand no. 60 roller chain is used to transmit power between a 13-tooth driving sprocket rotating at 300 rev/min and a 52-tooth driven sprocket. a) what is the allowable horsepower of this drive? b) estimate the center-to-center distance if the chain length is 82 pitches. c) estimate the torque and bending force on the driving shaft by the chain if the actual horsepower transmitted is 30 percent less than the corrected (allowable) power.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Thermal stresses are developed in a metal when its a) initial temperature is changed b) final temperature is changed c) density is changed d) thermal deformation is prevented e) expansion is prevented f) contraction is prevented

Answers: 2

Answer

Engineering, 04.07.2019 18:10

A-mn has a cubic structure with a0 0.8931 nm and a density of 7.47 g/cm3. b-mn has a different cubic structure, with a0 0.6326 nm and a density of 7.26 g/cm3. the atomic weight of manganese is 54.938 g/mol and the atomic radius is 0.112 nm. determine the percent volume change that would occur if a-mn transforms to b-mn.

Answers: 2

Answer

You know the right answer?

Convection ovens operate on the principle of inducing forced convection inside the oven chamber with...

Questions