![subject](/tpl/images/cats/User.png)
Engineering, 07.04.2020 00:57 FlowerChild1229
Consider a practical problem where the thermal conductivity variation with temperature is significant, and cannot be ignored. In a paragraph or so, discuss a viable solution method for this type of problem. Clearly explain why you chose this solution method.
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afluid flows with a velocity field given by v=(x/t)i.. determine the local and convective accelerations when x=3 and t=1.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
For the closed feedwater heater below, feedwater enters state 3 at a pressure of 2000 psia and temperature of 420 °f at a rate of ix10 ibhr. the feedwat extracted steam enters state 1 at a pressure of 1000 psia and enthalpy of 1500 btu/lbm. the extracted er leaves at an enthalpy of 528.7 btu/lbm steam leaves as a saturated liquid. (16) a) determine the mass flow rate of the extraction steam used to heat the feedwater (10) b) determine the terminal temperature difference of the closed feedwater heater
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Awall of 0.5m thickness is to be constructed from a material which has average thermal conductivity of 1.4 w/mk. the wall is to be insulated with a material having an average thermal conductivity of 0.35 w/mk so that heat loss per square meter shall not exceed 1450 w. assume inner wall surface temperature of 1200°c and outer surface temperature of the insulation to be 15°c. calculate the thickness of insulation required.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
You know the right answer?
Consider a practical problem where the thermal conductivity variation with temperature is significan...
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 27.07.2019 12:00
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/en.png)
English, 27.07.2019 12:00
![question](/tpl/images/cats/istoriya.png)
History, 27.07.2019 12:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 27.07.2019 12:00
![question](/tpl/images/cats/mat.png)
Mathematics, 27.07.2019 12:00
![question](/tpl/images/cats/mat.png)
Mathematics, 27.07.2019 12:00
![question](/tpl/images/cats/istoriya.png)
History, 27.07.2019 12:00
![question](/tpl/images/cats/mat.png)
Mathematics, 27.07.2019 12:00
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/istoriya.png)
History, 27.07.2019 12:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
English, 27.07.2019 12:00
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 27.07.2019 12:00