subject
Engineering, 31.03.2020 05:03 hmjjones

In the 1960s through 1980s, a medical filter manufacturer in Ann Arbor discharged 1,4-dioxane (an industrial solvent) directly into the environment, where it ultimately leached into underlying groundwater aquifers. A plume of 1,4-dioxane has been spreading under Ann Arbor and could pose water quality risks if it reaches Barton Pond, which supplies 85% of the city's drinking water. a) Barton Pond contains 1.5 billion gallons (5.68 million m3) of water and initially contains no 1,4-dioxane. Assume the pond is perfectly mixed with one stream flowing in and out at a rate of 1 m3/s. Suppose the plume enters the pond at a rate of 0.1 m3/s and contains 50 mg/L of 1,4-dioxane, which has a first-order decay constant of 6.4*105 s1. What is the steady-state concentration of 1,4-dioxane in the pond? b) Local water authorities find a way to divert the plume such that 1,4-dioxane is no longer entering the pond. How long will it take for the 14-dioxane concentration in the pond to reach the Michigan Department of Environmental Quality's new allowable drinking water level of 7.2 ug/L? c) The EPA classifies 1,4-dioxane as a probable carcinogen with a potency factor of 0.011 (mg/kg/d)1. If the water contains the EPA's allowable limit of 7.2 μg/L of 1,4-dioxane, calculate the carcinogenic risk based on the default EPA exposure factors over a lifetime for ingestion of potable water in an average adult. Is the water safe to drink based on the "rule of thumb" discussed in class?

ansver
Answers: 2

Another question on Engineering

question
Engineering, 04.07.2019 18:10
Apipe with an outside diameter of 15 cm is exposed to an ambient air and surrounding temperature of -20°c. the pipe has an outer surface temperature of 65°c and an emissivity of 0.85. if the rate of heat loss from the pipe surface is 0.95 kw per meter of length, the external convective heat transfer coefficient (h) is: (a) 12.5 w/m"k (b) 18.6 w/mk (c) 23.7 w/mk (d) 27.9 w/mk (e) 33.5 w/mk
Answers: 1
question
Engineering, 04.07.2019 18:10
Slip occurs via two partial dislocations because of (a) the shorter path of the partial dislocation lines; (b) the lower energy state through partial dislocations; (c) the charge balance.
Answers: 1
question
Engineering, 04.07.2019 19:20
To design a steam turbine to produce 12,000 hp power. a engineer comsiders using a steady state stean low st 1160fr and engineer considers using a steady state steam flow at 1160°r and 450 psia to drive this steam turbine. the exhaust of the steam is cooled by the lake (vacuum). heat losing to the surroundings is measured at a rate of 555.55 btu/s. (a) sketch the system with the given conditions. (b) neglecting kinetic and potential energy changes from inlet to exit, determine the volumetric flow rate of the steam at the inlet, (ft'/hr). must clearly show unit conversions at crtical terms.
Answers: 1
question
Engineering, 04.07.2019 19:20
Apreheater involves the use of condensing steam at 100°c on the inside of a bank of tubes to heat air that enters at 1 atm and 25°c. the air moves at 5 m/s in cross flow over the tubes. each tube is 1 m long and has an outside diameter of 10 mm. what is the minimum value of nl needed to achieve an outlet temperature of t 75 c? what is the corresponding pressure drop across the tube bank?
Answers: 3
You know the right answer?
In the 1960s through 1980s, a medical filter manufacturer in Ann Arbor discharged 1,4-dioxane (an in...
Questions
question
Mathematics, 06.10.2019 17:30
question
Mathematics, 06.10.2019 17:30
Questions on the website: 13722359