subject
Engineering, 02.03.2020 20:14 eelebron0905

A horizontal curve on a 4-lane highway (two lanes on each direction with no median) has a superelevation of 6% and a central angle of 40 degrees. The PT of the curve is at station 322+50 and the PI is at station 320+08. The road has 10ft lanes and 8ft shoulders on both sides with high retaining walls going up immediately next to the shoulders. What is the highest safe speed of this curve (highest in 5mph increments) and what is the station of the PC?

ansver
Answers: 1

Another question on Engineering

question
Engineering, 03.07.2019 14:10
Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.
Answers: 3
question
Engineering, 04.07.2019 18:10
At 12 noon, the count in a bacteria culture was 400; at 4: 00 pm the count was 1200 let p(t) denote the bacteria cou population growth law. find: (a) an expression for the bacteria count at any time t (b) the bacteria count at 10 am. (c) the time required for the bacteria count to reach 1800.
Answers: 1
question
Engineering, 04.07.2019 19:10
Afoot bridge is made as a simple deck, 4 m long, with a cross section 2 m (wide) and 20 cm thick, and made of wood. the deck is supported at the two ends. the maximum load allowable on the bridge is 10 tons, provided it is uniformly distributed on the deck. to sense this load, a strain gauge is placed at the center of the bridge and its resistance is monitored. if the sensor has a nominal resistance of 350 s2 and a gauge factor of 3.6, what is the reading of the strain gauge at maximum load? the modulus of elasticity for the wood used in the construction is 10 gpa.
Answers: 2
question
Engineering, 06.07.2019 02:30
Plot schematically the tensile stress versus strain curves for a typical thermoplastic material at a temperature below its glass transition temperature (tg and at a temperature above its tg, respectively. do the same for a typical thermosetting material. list in a table any differences or similarities between the two materials at t> tg and t < tg, respectively, and relate them to the structures of the two types of polymers
Answers: 3
You know the right answer?
A horizontal curve on a 4-lane highway (two lanes on each direction with no median) has a supereleva...
Questions
question
Mathematics, 16.09.2020 18:01
question
Mathematics, 16.09.2020 18:01
question
Mathematics, 16.09.2020 18:01
question
Mathematics, 16.09.2020 18:01
question
Mathematics, 16.09.2020 18:01
question
Mathematics, 16.09.2020 18:01
question
Mathematics, 16.09.2020 18:01
question
Chemistry, 16.09.2020 18:01
question
Mathematics, 16.09.2020 18:01
question
Mathematics, 16.09.2020 18:01
question
Mathematics, 16.09.2020 19:01
question
Mathematics, 16.09.2020 19:01
question
Mathematics, 16.09.2020 19:01
question
Mathematics, 16.09.2020 19:01
question
Mathematics, 16.09.2020 19:01
question
Mathematics, 16.09.2020 19:01
question
English, 16.09.2020 19:01
question
Mathematics, 16.09.2020 19:01
question
Mathematics, 16.09.2020 19:01
question
Mathematics, 16.09.2020 19:01
Questions on the website: 13722366