Consider the following 10 "design rules" for electromechanical products.
Do these seem like r...
![subject](/tpl/images/cats/User.png)
Engineering, 25.02.2020 18:03 yonna74
Consider the following 10 "design rules" for electromechanical products.
Do these seem like reasonable guidelines? Under what circumstances could one rule conflict with another one? How should such a trade-off be settled?
1. Minimize parts count
2. Use modular assembly
3. Stack assemblies
4. Eliminate adjustments
5. Eliminate cables
6. Use self-fastening parts
7. Use self-locating parts
8. Eliminate reorientation
9. Facilitate parts handling
10. Specify standard parts
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Asimple rankine cycle uses water as the working fluid. the water enters the turbine at 10 mpa and 480c while the condenser operates at 6 kpa. if the turbine has an isentropic efficiency of 80 percent while the pump has an isentropic efficiency of 70 percent determine the thermal efficiency
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Refrigerant-134a enters the compressor of a refrigerator as superheated vapor at 0.14 mpa and -10°c at a rate of 0.05 ka/s and leaves at 0.8 mpa and 50°c. the refrigerant is cooied in the condenser to 0.72 mpa and 26'c. it is then throttled to 0.15 mpa. sketch the t-s diagram for the system and evaluate: 6) the rate of heat removai from the refrigerated space (kw), it) the power input to the compressor (kw), ii) the isentropic efficiency of the compressor (%), and iv) the cop of the refrigerator.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
What are the major differences between injection molding and extrusion?
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 04:20
Amachine of mass 140 kg is mounted on springs of stiffness 1.4x10° n/m and in parallel witha viscous damper of unknown damping coefficient. the machine is subject to a harmonic excitation of 200sin150t n. the phase angle is measured as 2.58 rad. what is the damping coefficient of the viscous damper?
Answers: 2
You know the right answer?
Questions
![question](/tpl/images/cats/en.png)
English, 05.12.2019 18:31
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 05.12.2019 18:31
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 05.12.2019 18:31
![question](/tpl/images/cats/geografiya.png)
Geography, 05.12.2019 18:31
![question](/tpl/images/cats/biologiya.png)
Biology, 05.12.2019 18:31
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 05.12.2019 18:31
![question](/tpl/images/cats/mat.png)
Mathematics, 05.12.2019 18:31
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/istoriya.png)