Engineering, 25.02.2020 01:05 Sushmitarai9416

Part A - Calculate Poisson's ratio

A square steel bar has a length of 5.4 ft and a 2.8 in by 2.8 in cross section and is subjected to axial tension. The final length is 5.40314 ft . The final side length is 2.79940 in . What is Poisson's ratio for the material?

Part B - Calculate the load

A square steel bar has a length of 3.6 ft and a 1.3 in by 1.3 in cross section and is subjected to axial compression. Under load, the thickness becomes 1.30019 in . If the modulus of elasticity is E = 2.9×104 ksi and Poisson's ratio is ? = 0.27; what is the magnitude of the load that was applied to the bar?

Part C - Maximum load

A slider with a square hole is mounted on the bar described in part B (Figure 1) . The largest load the bar ever carries is 68 kip . What is the minimum side length of the square hole so that it will not bind on the bar?

Answers: 1

Show answers

Another question on Engineering

Engineering, 03.07.2019 14:10

Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Water at 70°f and streams enter the mixing chamber at the same mass flow rate, determine the temperature and the quality of the exiting stream. 0 psia is heated in a chamber by mixing it with saturated water vapor at 20 psia. if both streams enters the mixing chamber at the same mass flow rate, determine the temperature and the quality of the existing system.

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Ahot wire operates at a temperature of 200°c while the air temperature is 20°c. the hot wire element is a tungsten wire of 5 um diameter and 2 mm in length. plot using excel current, heat transfer and heat generated by the wire for air velocity varying from 1-10 m/s in steps of lm/s? matlab the sensor voltage output, resistance, or assume nu 0.989 re033pr13 take air properties at tr (200°c20°c)/2 = 110°c properties of tungsten: c 0.13 kj/kg.k 3 p 19250 kg/m k (thermal conductivity) = 174 w/m.k

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Compute the pressure drop of 30°c air flowing with a mean velocity of 8 m/s in a circular sheet-metal duct 300 mm in diameter and 15 m long. use a friction factor, f 0.02, and pair = 1.1644 kg/m a. 37.26 pa b. 25.27 pa n c. 29.34 pa d. 30.52 pa

Answers: 1

Answer

You know the right answer?

Part A - Calculate Poisson's ratio

A square steel bar has a length of 5.4 ft and a 2.8...

Questions