![subject](/tpl/images/cats/User.png)
Engineering, 19.12.2019 00:31 martinbricein10
The critical resolved shear stress for copper is 0.48 mpa (70 psi). determine the maximum possible yield strength for a single crystal of cu pulled in tension. (jr., 10/2018, p. p-43) jr., w. c., rethwisch, d. g. (10/2018). fundamentals of materials science and engineering: an integrated approach, enhanced etext, 5th edition [vitalsource bookshelf version]. retrieved from vbk: //9781119175506 always check citation for accuracy before use.
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Which one from below is not one of the reasons of planning failures? (clo3) a)-planner is careless. b-planner spend less time in the field but more time on the desk c)-planner is not qualified d)-planner does not have sufficient time to properly plan
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Journeyman training is usually related (clo2) a)-to specific tasks b)-to cost analysis of maintenance task c)-to control process to ensure quality d)-to installation of machinery
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Derive the correction factor formula for conical nozzle i=-(1+ cosa) and calculate the nozzle angle correction factor for a nozzle whose divergence hal-fangle is 13 (hint: assume that all the mass flow originates at the apex of the cone.
Answers: 3
You know the right answer?
The critical resolved shear stress for copper is 0.48 mpa (70 psi). determine the maximum possible y...
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 27.07.2019 18:00
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/en.png)
English, 27.07.2019 18:00
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/geografiya.png)
Geography, 27.07.2019 18:00
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
History, 27.07.2019 18:00
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/istoriya.png)
History, 27.07.2019 18:00
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/en.png)
English, 27.07.2019 18:00
![question](/tpl/images/cats/istoriya.png)
History, 27.07.2019 18:00
![question](/tpl/images/cats/istoriya.png)
History, 27.07.2019 18:00