subject
Engineering, 14.11.2019 03:31 Dreamer05

An inventor has proposed a modern manifestation of an atkinson cycle engine concept to control engine load without throttling and thus improve efficiency at part load. the concept uses late intake valve closing (ivc) which effectively creates an expansion ratio larger than the effective compression ratio. the engine is 4-stroke, spark-ignited, and operates unthrottled. the engine has a clearance volume of 50 cm3 and a displaced volume of 600 cm3 per cylinder. the fresh working fluid is a lean mixture of methane (ch4 ) and air at an equivalence ratio φ = 0.9. the lower heating value of methane is 50 mj/kg. the cylinder contents behave as an ideal gas with constant specific heats (γ = 1.25, r = 0.300 kj/kg-k). the cycle processes are described below:

intake process (5-6) and constant pressure work process (6-1)

for the first part of the process (5-6), the piston descends from tdc to bdc. for the second part of the process (6-1), the piston ascends half-way into the geometric compression stroke while the intake valve is still open. throughout the intake process 5-6, fresh fuel-air mixture is inducted into the cylinder and mixed with the residual gas, while during 6-1 mixture is displaced from the cylinder; the cylinder pressure remains constant at 100 kpa during the process 5-6-1. when the intake valve is closed (state 1), the temperature of the cylinder contents is 440 k.

compression process 1-2

compression is isentropic. cylinder pressure rises as the piston ascends towards tdc. effective compression

ansver
Answers: 2

Another question on Engineering

question
Engineering, 04.07.2019 19:10
Afoot bridge is made as a simple deck, 4 m long, with a cross section 2 m (wide) and 20 cm thick, and made of wood. the deck is supported at the two ends. the maximum load allowable on the bridge is 10 tons, provided it is uniformly distributed on the deck. to sense this load, a strain gauge is placed at the center of the bridge and its resistance is monitored. if the sensor has a nominal resistance of 350 s2 and a gauge factor of 3.6, what is the reading of the strain gauge at maximum load? the modulus of elasticity for the wood used in the construction is 10 gpa.
Answers: 2
question
Engineering, 06.07.2019 02:30
1in2 processor chip can be modelled as an isothermal plane wall of silicon, isothermal on both sides. the power input to the bottom of the plane wall, or the processing power of the chip, often called the thermal design power (tdp), is 100w. assume the periphery is adiabatic. the silicon is 400 microns thick. the temperature at the junction, or in this case on the bottom of the isothermal plane wall, is 85°c. what is the top surface temperature, assuming that the only mode of heat transfer is conduction
Answers: 1
question
Engineering, 06.07.2019 04:10
Consider a power plant with water as the working fluid that operates on an ideal rankine cycle. it has a net power output of 45mw. superheated steam enters the turbine at 7mpa and 500°c (h=3411.4 kj/kg; s=6.8 kj/kg k) and is cooled in the condenser at a pressure of 10 kpa by running cooling water from a lake through the tubes of the condenser at a rate of 2000 kg/s. (a) show the cycle on a t-s diagram (a right schematic is fine - you do not need to calculate the temperatures at each point); (b)-determine the work done by the turbine and the pump in kj/kg; (c)-the mass flow rate of water used by the power plant; (d)-the thermal efficiency of the cycle; (e)-the temperature rise of the cooling water. assume the cooling water is incompressible with cp 4.18 kj/kg°c.
Answers: 3
question
Engineering, 06.07.2019 04:10
Aheat pump with refrigerant-134a as the working fluid is used to keep a space at 25°c by absorbing heat from geothermal water that enters the evaporator at 500c at a rate of 0.065 kg/s and leaves at 40°c. the refrigerant enters the evaporator at 20°c with a quality of 23 percent and leaves at the inlet pressure as saturated vapor. the refrigerant loses 300 w of heat to the surroundings as it flows through the compressor and the refrigerant leaves the compressor at 1.4 mpa at the same entropy as the inlet. determine: (a) the degrees of subcooling of the refrigerant in the condenser, b)-the mass flow rate of the refrigerant . (c) the heating load and the cop of the pump, and d)-the theoretical minimum power input to the compressor for the same heating load.
Answers: 3
You know the right answer?
An inventor has proposed a modern manifestation of an atkinson cycle engine concept to control engin...
Questions
question
Mathematics, 03.06.2020 19:02
question
Mathematics, 03.06.2020 19:02
question
Mathematics, 03.06.2020 19:02
Questions on the website: 13722365