question 9 of 10 (1 point) jump to question:
what safety measures can employers use wh...
![subject](/tpl/images/cats/User.png)
Engineering, 01.10.2019 19:20 raquelqueengucci25
question 9 of 10 (1 point) jump to question:
what safety measures can employers use when workers are on a supported scaffold more than 10 feet above the working surface?
a.
top rail or guardrail
b.
personal fall arrest system or toeboard
c.
mid rail or toeboard
d.
personal fall arrest system or guardrail
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aflywheel accelerates for 5 seconds at 2 rad/s2 from a speed of 20 rpm. determine the total number of revolutions of the flywheel during the period of its acceleration. a.5.65 b.8.43 c. 723 d.6.86
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Which of the following ziegler nichols tuning methods the response of the controller to a step input should exhibit an s-shaped curve? a)-open loop mode b)-closed loop mode c)-both modes (open & closed) d)-none of the modes (open & closed)
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Air is compressed isentropically from an initial state of 300 k and 101 kpa to a final temperature of 1000 k. determine the final pressure using the following approaches: (a) approximate analysis (using properties at the average temperature) (b) exact analysis
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
Afoot bridge is made as a simple deck, 4 m long, with a cross section 2 m (wide) and 20 cm thick, and made of wood. the deck is supported at the two ends. the maximum load allowable on the bridge is 10 tons, provided it is uniformly distributed on the deck. to sense this load, a strain gauge is placed at the center of the bridge and its resistance is monitored. if the sensor has a nominal resistance of 350 s2 and a gauge factor of 3.6, what is the reading of the strain gauge at maximum load? the modulus of elasticity for the wood used in the construction is 10 gpa.
Answers: 2
You know the right answer?
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 03.05.2021 23:40
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 03.05.2021 23:40
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 03.05.2021 23:40
![question](/tpl/images/cats/mat.png)
Mathematics, 03.05.2021 23:40
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 03.05.2021 23:40
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 03.05.2021 23:40
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 03.05.2021 23:40