![subject](/tpl/images/cats/User.png)
Engineering, 14.09.2019 01:30 Calliedevore
Avertical piston-cylinder device initially contains 0.1 m3 of air at 400 k and 100 kpa. at this initial condition, the piston is resting on a stop. the piston-cylinder device is connected to a supply line with air at 400 k and a pressure of 500 kpa. the valve between the supply line and the piston-cylinder device is opened and is left open until the pressure in the piston-cylinder device reaches 500 kpa. the piston is observed to start moving when the pressure in the cylinder is 200 kpa and the piston continues to rise until it reaches a second stop. at the second stop, the piston-cylinder volume is 0.2 m3 . the final temperature and pressure in the piston-cylinder device are 440 k and 500 kpa, respectively. molecular weight of air = 28.97 kg/kmol. determine heat transfer (kj) during the entire process. indicate whether it is into the system or out of the system.
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Which one from below is not one of the reasons of planning failures? (clo3) a)-planner is careless. b-planner spend less time in the field but more time on the desk c)-planner is not qualified d)-planner does not have sufficient time to properly plan
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Describe one experiment in which the glass transition temperature and melting temperature of a totally amorphous thermoplastic material can be determined. show the relevant experimental results in a diagram which should be properly annotated with the two temperatures clearly marked. what is likely to happen to the curve in the diagram if the amorphous polymer is replaced by a thermosetting type?
Answers: 2
You know the right answer?
Avertical piston-cylinder device initially contains 0.1 m3 of air at 400 k and 100 kpa. at this init...
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 23.12.2020 01:00
![question](/tpl/images/cats/mat.png)
Mathematics, 23.12.2020 01:00
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 23.12.2020 01:00
![question](/tpl/images/cats/mat.png)
Mathematics, 23.12.2020 01:00
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 23.12.2020 01:00
![question](/tpl/images/cats/es.png)
Spanish, 23.12.2020 01:00
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 23.12.2020 01:00
![question](/tpl/images/cats/en.png)
English, 23.12.2020 01:00
![question](/tpl/images/cats/himiya.png)
Chemistry, 23.12.2020 01:00
![question](/tpl/images/cats/mat.png)
Mathematics, 23.12.2020 01:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 23.12.2020 01:00
![question](/tpl/images/cats/mat.png)
Mathematics, 23.12.2020 01:00
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 23.12.2020 01:00