When using an air wrench_
a. keep your body stance balanced
b hold onto the compressor h...
![subject](/tpl/images/cats/User.png)
Engineering, 27.08.2019 05:10 cacaface311
When using an air wrench_
a. keep your body stance balanced
b hold onto the compressor hose with one hand
c hold the impact socket a few inches away from the material
d. use handheld sockets that are the right size
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
Apressure vessel with an r/t 20 cannot be treated as thin walled vessel. a)-trune b)- false
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 02:30
1in2 processor chip can be modelled as an isothermal plane wall of silicon, isothermal on both sides. the power input to the bottom of the plane wall, or the processing power of the chip, often called the thermal design power (tdp), is 100w. assume the periphery is adiabatic. the silicon is 400 microns thick. the temperature at the junction, or in this case on the bottom of the isothermal plane wall, is 85°c. what is the top surface temperature, assuming that the only mode of heat transfer is conduction
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 03:20
What is the maximum height from which a mass of 30 kg can fall on to a flange on the lower end of a vertical rod of length 1.0 m and diameter 20 mm, the upper end being rigidly fixed, if the stress in the rod is not to exceed 80 mpa? the tensile modulus of the rod is 200 gpa.
Answers: 3
You know the right answer?
Questions
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 03:31
![question](/tpl/images/cats/biologiya.png)
Biology, 05.01.2020 03:31
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 05.01.2020 03:31
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 03:31
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 03:31
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 03:31
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 05.01.2020 03:31
![question](/tpl/images/cats/himiya.png)
Chemistry, 05.01.2020 03:31
![question](/tpl/images/cats/istoriya.png)
History, 05.01.2020 03:31