Engineering, 11.07.2019 02:20 milak23

Adisk-shaped part is to be cast out of aluminum. the diameter 500 mm and thickness = 20 mm. if the mold constant = 3.0 s/mm2 in chvorinov's rule, how long will it take the casting to solidify, in minutes?

Answers: 2

Show answers

Answers

Answer from: asharrogers17

t =253.8s

Explanation:

Chvorinov's Rule can be written as:

$t=B(\frac{V}{A} )^{n}$

where t is the solidification time,

V is the volume of the casting,

A is the surface area of the casting that contacts the mold,

n is a constant

B is the mold constant

The S.I. units of the mold constant B are s/m2.

According to Askeland, the constant n is usually 2.

$V=\frac{\pi D^{2}h }{4} = 3.9*10^6$ mm3

$As=\pi D h+2\frac{\pi }{4} D^{2} =0.424*10^6$ mm2

V/A=9.198 mm

t = 3.0*9.198^2 =253.8s

Answer from: 163565

Chvorinov's Rule with Askeland Method: t = 4.286694102 minutes

Chvorinov's Rule with Degarmo Method:

Minimum time required at constant n = 1.5 : t = 1.408751434 minutesMaximum time required at constant n = 2.0 : t = 4.286694102 minutes

Explanation:

Data:

Aluminum disc

Diameter (D) = 500 mm

Thickness = Height (h) = 20 mm

Mold Constant (C) = 3.0 sec / $mm^{2}$

Required:

Solidification time (t) in minutes = ?

Formula:

The solidification time can be found by using the Chvorinov's Rule:

$t = C (\frac {V}{A})^{n}$

Where;

t = solidification time

C = mold constant

V = Volume of disc

A = Surface area of disc

n = constant

Note: According to Askeland n = 2.0 and According to Degarmo n varies 1.5 to 2.0 therefore , we will do for both method and by Degarmo method we can predict maximum and minimum solidification time.

Solution:

First, we will find the volume of the disc

disc = cylinder

therefore, Volume of cylinder is given by:

$V = \frac{\pi }{4} * D^{2} * H$

Where:

V = Volume of Cylinder

H = Height of disc

D = Diameter of disc

Now, putting dimensional values in above equation

$V = \frac{\pi }{4} * 500^{2} *20$

V = 3926990.817 $mm^{3}$

Second, we will find the surface area of the disc

Therefore, surface area of cylinder is given by:

$A = (\pi * D * H) + (2 * \frac{\pi }{4} * D^{2} )$

Where:

A = Surface area of disc

D = Diameter of disc

H = Height of disc

Now, putting dimensional values in above equation

$A = (\pi * 500 * 20) + (2 * \frac{\pi }{4} * 500^{2} )$

A = 424115.0082 $mm^{2}$

Finally, Moving towards the final solution

Chvorinov's Rule with Askeland Method n = 2:

Rewriting the equation:

$t = C (\frac {V}{A})^{2}$

Putting the dimensional and constants values in the equation

$t = 3.0 (\frac {3926990.817}{424115.0082})^{2}$

t = 257.2016461 seconds

Converting to minutes

t = 4.286694102 minutes

Chvorinov's Rule with Degarmo Method n = 1.5 (Minimum Solidification Time)

Rewriting the equation:

$t = C (\frac {V}{A})^{2}$

Putting the dimensional and constants values in the equation

$t = 3.0 (\frac {3926990.817}{424115.0082})^{1.5}$

t = 84.52508604 seconds

Converting to minutes

t = 1.408751434 minutes

Chvorinov's Rule with Degarmo Method n = 2.0 (Maximum Solidification Time)

Rewriting the equation:

$t = C (\frac {V}{A})^{2}$

Putting the dimensional and constants values in the equation

$t = 3.0 (\frac {3926990.817}{424115.0082})^{2}$

t = 257.2016461 seconds

Converting to minutes

t = 4.286694102 minutes

Answer from: Quest

answer:

yes

explanation:

Answer from: Quest

answer:

clock

explanation:

always running (on) sing each hour (chime) and the clock face (front)

Another question on Engineering

Engineering, 04.07.2019 18:20

Find the minimum film thickness for a journal bearing with the data below. shaft diameter, d-50 mm, clearance ratio, cdratio? 0.001, shaft speed, n 2000 rpm; bearing length. i 200 mm; eccentricity ration, ? -0.55. ( note, cdratio-ca/d) the minimum film thickness is um

Answers: 2

Answer

Engineering, 04.07.2019 18:20

Apiston-cylinder device contains 0.1 m3 of liquid water and 0.9 m3 of water vapor in equilibrium at 800 kpa. heat is transferred at constant pressure until the temperature of water reaches 350 °c. determine (a) the quality of water at the initial state (b) the work associated with this process, (c) the heat associated with this process.

Answers: 2

Answer

Engineering, 04.07.2019 18:20

Prove the equivalence between the two statements of the 2nd law of thermodynamics (i.e., a violation of one statement leads to the violatio the other statement)

Answers: 2

Answer

Engineering, 05.07.2019 19:10

Tech a says never use a water hose to clean up dust after a repair. tech b says never use a floor scrubber to clean up dust after repairs. who is correct?

Answers: 1

Answer

You know the right answer?

Adisk-shaped part is to be cast out of aluminum. the diameter 500 mm and thickness = 20 mm. if the m...

Questions

Engineering, 15.12.2020 16:30

What is important to know when grinding a chisel face or edge...