Chemistry, 02.11.2021 23:00 trillralyn4060

Plz help me Pre-Lab Information

Purpose To model and observe stream processes, including factors that affect erosion and deposition
Time Approximately 45 minutes
Question What factors affect the power of a stream or river to cause erosion?
Summary In this lab, you will use a virtual model to observe stream behavior. You will model five scenarios involving a stream, and investigate the effect of water velocity, water volume, the stream slope, and the size of sediment on sand, pebbles, and various-sized rocks in a stream.
Lab Procedure
Prepare for the project.
Read through this guide before you begin, so you know the expectations for this lab.
If anything is not clear to you, be sure to ask your teacher.
Open the virtual lab.
Model a low-gradient, low-velocity stream.
Read the scenario.
You are on a research trip to observe pronghorn in the prairie grasslands of Colorado. As you observe a herd grazing next to a nearby stream, you notice storm clouds moving in overhead and feel rain beginning to fall. How does the stream act right now upon the objects in it?
Analyze the scenario and characterize the slope of the stream, the amount of rainfall, and the terrain of the area.
Press the “Go to the model.” button to open the modeling tool.
You can always return to the scenario by clicking the “?” button in the top-right corner.
On the left panel, choose the description for each parameter that would correctly model the scenario.
Press the “Check” button.
If all your descriptions are correct, proceed to step f.
If your descriptions are not all correct, analyze the scenario again and correct your descriptions. Click on the “Check” button. Do this step until all descriptions are correct. Then proceed to step f.
Observe what happens to the sand and pebbles in the stream.
When ready, press the “Pause” button and write your observations in the space below

Answers: 1

Show answers

Another question on Chemistry

Chemistry, 22.06.2019 01:30

Follow the steps provided in the simulation to add water to the graduated cylinder, select one of the three samples (copper, silver, or gold), set its mass to the values given in the statements below, and calculate its density. here is a summary of the steps required: add water by clicking and holding prepare a known volume of water button. until the desired volume of water has been added. if more than the desired volume is added, click the reset button. button and redo the procedure. a single click will add about 21.0 ml of water. to set the mass, click and hold weigh out metal button. until the desired amount of metal is added to the weighing pan. once the desired mass of the metal is added, release the button. transfer the metal to water and then click on calculate density button. to see how the density is calculated using water displacement to measure the volume of the solid. to save time you can approximate the initial volume of water to â±1 ml and the initial mass of the solid to â±1 g. for example, if you are asked to add 23 ml of water, add between 22 ml and 24 ml. which metals in each of the following sets will have equal density? check all that apply.

Answers: 1

Answer

Chemistry, 22.06.2019 13:30

Astudent is trying to create a table that compares hypotheses, theories, and laws. hypothesis theory law do scientific researchers formulate it? yes yes yes does it explain why things happen? yes yes no yes yes yes is it used to make predictions? no yes yes which of the following questions would most likely fill the blank in the table? is it an intelligent guess? is it newly formulated? is it based on observations? has it been proved?

Answers: 1

Answer

Chemistry, 22.06.2019 17:30

A650 ml sodium bromine solution has a bromide ion concentration of 0.245 m. what is the mass (g) of sodium bromide in solution? a) 103.b)0.00155.c)16400.d) 16.4.e) 0.159

Answers: 2

Answer

Chemistry, 22.06.2019 23:00

What is the average rate of the reaction between 10 and 20 s?

Answers: 1

Answer

You know the right answer?

Plz help me Pre-Lab Information

Purpose To model and observe stream processes, includi...

Questions