subject

Chemistry, 12.12.2020 23:50 EinsteinBro

Please help will mark the brainliest.

Please help will mark the brainliest.

ansver

Answers: 3

Show answers

Another question on Chemistry

question

Chemistry, 22.06.2019 12:30

Adilute aqueous potassium nitrate solution is

Answers: 1

question

Chemistry, 22.06.2019 14:30

Amixture that has two or more substances that are spread out evenly is called a. compound b. heterogeneous c. substance d. homogeneous

Answers: 1

question

Chemistry, 22.06.2019 20:00

Nitrogen dioxide decomposes according to the reaction 2 no2(g) ⇌ 2 no(g) + o2(g) where kp = 4.48 × 10−13 at a certain temperature. if 0.70 atm of no2 is added to a container and allowed to come to equilibrium, what are the equilibrium partial pressures of no(g) and o2(g)

Answers: 2

question

Chemistry, 22.06.2019 20:30

Calculate the percent composition by mass of each element in al(oh)3. use at least three significant figures.

Answers: 1

You know the right answer?

Please help will mark the brainliest.
...

Questions

question

Engineering, 26.07.2019 16:20

Water is the working fluid in a rankine cycle. steam enters the turbine at 1400 lbf/in^2 and 1000 degrees f. the condenser pressure is 2 lbf/in^2. bot...

question

Engineering, 26.07.2019 16:20

Which of the following dimensionless numbers govern the transition turbulent flow in an external forced convection analysis? numbers govern the trans...

question

Engineering, 26.07.2019 16:20

Put the four main steps of the injection molding process in correct order. (place the correct step number after the text line) a)- injection of plasti...

question

Engineering, 26.07.2019 16:20

Which dimensionless number can describe the rela boundary layers? umber can describe the relative thickness of the velocity and thermal a. biot b. nu...

question

Engineering, 26.07.2019 16:20

A½ inch diameter bolt is under a shear load of 4500 lb. determine the average shear stress on the bolt. assume the bolt is in single shear and is made...

question

Engineering, 26.07.2019 16:20

The pressure drop is the irreversible pressure loss between the inlet and the exit of a tube bank. a pressure loss has units of a. j 1 b. n c. pa d. w...

question

Engineering, 26.07.2019 16:20

What does the 13 in the ½-13 screw call-out stand for? a. thread pitch (distance between threads) b. major diameter of thread c. threads per inch d....

question

Engineering, 26.07.2019 16:20

The diesel cycle is very close to the otto cycle. what is a difference between the two air-standard cycles? a)-the diesel cycle assumes constant volu...

question

Engineering, 26.07.2019 16:20

One can expect the velocity boundary layer for laminar flow to be much thicker than the thermal boundary layer when the prandtl number is a. > >...

question

Engineering, 26.07.2019 16:20

Select a light w shape for a column subjected to an axial compressive load of 355 kips. the unbraced length of column is 16 ft and the ends are pinned...

question

Engineering, 26.07.2019 16:20

Which has more threads per inch: ¼-20 or an m8-1? a)- ¼-20 b)- м8-1 c)- same...

question

Engineering, 26.07.2019 16:20

Use the map of ohio that follows to find the average wind speed for columbus, ohio (5.5 m/s). a wind turbine located at byers mazda subaru near i 270...

question

Engineering, 26.07.2019 16:20

An a36 - 1.0 inch diameter steel tie rod is used to support a tensile load of 12,000 lb. determine the stress in the tie rod and calculate the factor...

question

Engineering, 26.07.2019 16:20

Afluid in direct contact direct contact with a stationary solid surface will have a velocity of zero in accordance with the condition. a. no-slip b. t...

question

Engineering, 26.07.2019 16:20

Steam enters an adiabatic turbine at 10 mpa and 500 °c and leaves at 30 kpa with a quality of 90 percent. neglecting the changes in kinetic and potent...

question

Engineering, 26.07.2019 16:20

Calculate the bending stress in a 1 ¾ in. x 12 in. x 18 ft. microllam lvl beam under the following load conditions: a)-2500 lb concentrated load at c...

question

Engineering, 26.07.2019 16:20

A) what is a free-cutting steel? explain. b) show the free energy vs. composition curve (schematic) for an alloy system a-b where there is a strong t...

question

Engineering, 26.07.2019 16:20

Acylindrical steel specimen is subjected to a stress of 100 mpa along the longitudinal axis. the undeformed specimen has a diameter do=10 mm and a len...

question

Engineering, 26.07.2019 16:20

What volume of helium is needed if a balloon is to lift a load of 1200kg (including the weight of the empty balloon)?...

question

Engineering, 26.07.2019 16:20

The backyard grill on the deck of a certain thermodynamics instructor, a rigid 0.5 m3 propane tank is left in the sun and gets hot. as a result, the p...

More questions: Chemistry Another questions

Questions on the website: 13722367