![subject](/tpl/images/cats/User.png)
Engineering, 20.09.2021 22:40 swelch2010
State the design issues while designing an ANN (Artificial Neural Network). If you don't know the answer then at least surf the internet and answer plz
![ansver](/tpl/images/cats/User.png)
Answers: 3
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 15:10
Ahouse has the following electrical appliance usage (1) single 40w lamp used for 4 hours per day (2) single 60w fan used for 12 hours per day (3) single 200w refrigerator that runs 24 hours per day with compressor run 12 hours and off 12 hours find the solar power inverter size in watt with correction factor of 1.25.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Shafts are machine elements that are used to a) carry axial loads b) direct shear loads c) transmit power d) rotate at constant speed e) none of the above circular and square shafts subjected to the same torque under the same circum behave a) the same way b) almost the same way
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
Afoot bridge is made as a simple deck, 4 m long, with a cross section 2 m (wide) and 20 cm thick, and made of wood. the deck is supported at the two ends. the maximum load allowable on the bridge is 10 tons, provided it is uniformly distributed on the deck. to sense this load, a strain gauge is placed at the center of the bridge and its resistance is monitored. if the sensor has a nominal resistance of 350 s2 and a gauge factor of 3.6, what is the reading of the strain gauge at maximum load? the modulus of elasticity for the wood used in the construction is 10 gpa.
Answers: 2
You know the right answer?
State the design issues while designing an ANN (Artificial Neural Network). If you don't know the an...
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 06.10.2019 19:00
![question](/tpl/images/cats/mat.png)
Mathematics, 06.10.2019 19:00
![question](/tpl/images/cats/himiya.png)
Chemistry, 06.10.2019 19:00
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 06.10.2019 19:00
![question](/tpl/images/cats/mat.png)
Mathematics, 06.10.2019 19:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/fizika.png)
Physics, 06.10.2019 19:00
![question](/tpl/images/cats/en.png)
English, 06.10.2019 19:00
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/pravo.png)
Law, 06.10.2019 19:00
![question](/tpl/images/cats/mat.png)
Mathematics, 06.10.2019 19:00
![question](/tpl/images/cats/es.png)
Spanish, 06.10.2019 19:00
![question](/tpl/images/cats/en.png)
English, 06.10.2019 19:00
![question](/tpl/images/cats/mat.png)
Mathematics, 06.10.2019 19:00
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
English, 06.10.2019 19:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 06.10.2019 19:00